0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How should a voltmeter be connected to measure voltage of a component?
Since voltage is electrical potential difference, to measure the voltage across a component, you place the voltmeter across, or in parallel with, the component.
What is a DV bridge?
A DV bridge is a type of converter box for video. It is a box-shaped electrical component that is used for converting analog video to Digital Video.
Analysing a circuit with a shorted component?
Analysing a circuit with a shorted component need specialised electrical test equipment.
What is a short load system?
Electrical load forecasting. "A good electrical load forecast has a direct and significant impact on costly generating unit startups and shutdowns, energy purchases, managing system demand as well as scheduling system upgrades based on predicted load growth."
What is the function of the load in the circuit?
It's a power outputThis answer is incorrect.A 'load' is the name given to any device supplied by the circuit. For example, a motor could be a load, or a resistor, a lamp, etc.
What is electrical power-consuming component?
Load
What part does a piece of wire play in an electrical circuit?
It is the component that brings the potential in the form of voltage to the load.
How should a voltmeter be connected to measure voltage of a component?
Since voltage is electrical potential difference, to measure the voltage across a component, you place the voltmeter across, or in parallel with, the component.
What term best describes an electrical circuit in which no current flows from the power source through the control component load and conductors?
A cold circuit
What part of circuit is not necessary for the circuit to be complete?
By definition an electrical circuit is a route or path that starts and finishes at the same place. So there is no part of an electrical circuit that is not necessary, because if there were it would not be an electrical circuit.An electrical circuit needs a power source. Conductors to transmit the voltage from the power source to the load. The final component of the electrical circuit is the load that you want to energize.If you remove any of the components there will be an open circuit and the load will be impossible to operate.
What component of an IRS creates an electrical charge?
What component of ied creates electrical charge
What is An electrical load is?
Load is simply any thing which dissipate electrical energy.
The object that uses up the energy being delievered in an electrical circuit is called the?
Any electrical appliance would be the object eg. a motor, a light, a heater etc
How are power dissipated in a load or in a resistor?
Due to energy usage and/or the reduction in conductance (increase in resistance) in a given load or resistor, some electrical energy is lost through that component. As such, a proportional drop in current and voltage occurs.
Explain why 3 phase induction motor at no load operates at a very low power factor?
An induction motor electrically appears much like an inductor with a resistive component. The resistive component is reflective of the mechanical power which the motor delivers. There are also some true resistive losses in the motor widings, but these are relatively smalll. At no load both these contribute to the total electrical resistive component of the IM. The resistive component at no load however will be small compared to the IM's inductance, resulting in a very low power factor. As the mechanical load on the motor is increased its effective electrical resistive component increases and so does its power factor. Another way of thinking about this is that a circuit's power factor is indicative of its electrical resistance, which dissipates watts. At no load very little actual electrical power (watts) is required to rotate the IM, so its power factor is low. If the IM is driving a large mechanical load more actual power must be delivered to the IM and this is indicated by a much larger power factor. _____ Under no load slip is almost zero, i.e.. there is almost no induced current in the inner coil. So power factor which is induced power to input power ratio is small. As load increases, slip increases for a given motor and so does the induced current and the torque generated in turn to run the load.
What are the four components of an interface?
electrical component, mechanical component, functional component and procedural component
Light wave is composed of two components an electrical component and a component?
the answer is: magnetic...magnetic and electrical
