0
there is may ways ! voltage normally less than 6 . Just listen your gun that and turn the voltage down as long as you cant hear a static noise and then just bit more ! That is the way i do it but every gun needs different voltage. Contact screw matters to as a gap with armature bar ! I hope that this helps
Wiki User
∙ 12y ago
Wiki User
∙ 10y agoDepends on what machines you're using and how they are set up. If you want to learn that bad, go get an apprenticeship by any means possible and don't be lazy. Online learning is not where or how you do it.
Wiki User
∙ 12y agoThe setting of your power supply means little when compared to the setting of the machine that you are shading with. The actual voltage should be around 6, but you will want to ensure that your machine is set up for a fairly long stroke in relation to your front spring and gap of tension so that you are delivering a smooth and packing stroke without chewing up the skin. You will want roughly the width of a nickel between your contact screw and front spring, and you may also have to adjust the tension of your rear spring to your frame to give you the best results. So play around with it on your thighs and find a setting that you are good with, and tune and play around with your machines too. They need regular maintenance and tuning like anything else.
Add your answer:
Earn +20 pts
How do you log into a iPad?
press power button ON, supply the security code password if you set it ON.
How do you setup tattoo machine for coloring?
The machine used for shading should be the one set up with the longest front spring as well as armature bar. Set the contact point gap at about a nickel's width for shading, a dime's width for lining. Run the tattoo machine for shading slightly slower. Don't go bigger than a five mag for beginners. Use it like a brush.
How do you make power supply variable?
A variable power supply is one whose output voltage (or current) can be adjusted and therefore set to a desired figure. They are used in development and design odf circuits, eliminating the need for possibly many power supplies of different output voltages. Once a circuit is connected to it, the output would not normally be changed.
How high or low should the tattoo power supply box be set at?
It depends on what yours using it for. I use 12 ish
What is A name for a predefined set of formatting characteristics including font alignment and cell shading?
Table Style
What power do illegal monopolies use to drive out competition?
Illegal monopolies are those that can be shown to use their power to suppress competition. A monopolist has the power to dominate markets--the ability to set the price by altering supply.
Does shading a tattoo take long?
Previous response: Yes LIke 1 hour Additional respone: Above answer seems quite short and dumb...the time it takes to shade a tattoo depends on the size of the tattoo and the amount of shading you wish to put in it, and the detail of shading. So if you use a lot of shading variations and want to put in a lot of detail it will obviously take longer than if you are doing something with simple shading. Set up a system with your washes to make the shading easier. I normally have a full black and then half black half distilled, and then a few other lighter ones down to a really light that i use for portraits for really soft shading. If you have a picture to work off for your shading you'll be able to see what parts require the darker wash and which requires lighter.
Can you use canon G9 as a webcam?
It would be better to supply your camera with power by using a suitable AC adapter and to set the 'Auto power off/down' camera's option to 'off'.
What charger goes to Coleman cmz984 bug zapper?
The CMZ984 takes 6 volts DC at about 850 ma or 0.85 Amp. The problem is finding a plug that will attach to the Coleman charging port. Use the Radio Shack universal DC power supply. This is a little unit that comes with an assortment of plugs and has a number of switches on the Radio Shack DC power supply. (1)-Find a plug inside of the Universal DC power supply that fits without forcing, (2)-set the voltage to 6 volts and (3)-the polarity to "+". When the universal power supply is plugged into the bug zapper and the universal DC power supply set at 6 volts, turn on the BUG ZAPPER. If the lights inside turns on when the battery is dead then you probably have all switches set correctly. At yard sales, this UNIVERSAL power supply sells for about $1. It comes with a number of different plugs. Don't forget to write the voltage and polarity on the bottom of the bug zapper for the next time.
What amp to set a tattoo power supply?
set your voltage first to around 4-6v for rotary 8-9 for regular guns and thenadjustthe amps until the gun sounds right.
How do you set up a PC in France?
On the power supply of your PC change the voltage from 110 to 220. You then need to have a European power cable, and plug it in like you would in the states. Everything else is exactly the same.
Can you change a US power supply on a PC to a UK power supply?
Yes. Most Power supplies don't care what frequency they run off, so 50 or 60 is not an issue. If your power supply has a voltage select switch on it, then you are all set: When you plug in to 220v, slide the switch across to 220/240V. If not, then you will have to swap the power supply for one that does. If your system uses a standard ATX PSU, then it is simple and cheap. If it uses a custom smaller one, then they are more expensive. The power supply will have a compliance label on it that will specify what it can use. Check that for full details. Many notebook power supplies can use anything that is vaguely electricity-like. Rub them on your woolly jumper fast enough and they'll probably work. Again, check the label.
