The purpose of a voltmeter is to indicate the potential difference between two points in a circuit.When a voltmeter is connected across a circuit, it shunts the circuit. If the voltmeter has a low resistance,it will draw a substantial amount of current. This action lowers the effective resistance of the circuit andchanges the voltage reading.
Nothing will happen to the resistance of the circuit. However, with the switch open, it will be 'seen' as having infinite resistance from the supply side.
The correct term is 'current', not 'amperage'. The answer is that nothing will happen to the resistance. Having said that, changing the resistance will cause current to change for a fixed value of voltage.Resistance is determined by the length, cross-sectional area, and resistivity of a material. Resistivity is affected by temperature, so resistance is also therefore indirectly affected by temperature. Only by changing one of these variables will the resistance change.Since the ratio of voltage to current will tell us what the resistance of a circuit happens to be (it's not affected by that ratio) for a particular ratio, the ratio will increase (as per your question) if the resistance increases. But it's not the ratio that's affecting resistance, its the resistance affecting the ratio!
When the frequency is zero(i.e when dc power is supplied), capacitor is open is treated as open circuit having infinite resistance.
The effect the multimeter might have on the circuit when inserted to measure the current is to increase the circuit resistance and decrease the available voltage to the circuit. This is because the multimeter in amps or milliamps mode does have a small resistance which is not zero, so by Ohm's law, there is a voltage drop across the multimeter; small, but not zero. Usually this effect is small. One way to compensate is to start by measuring voltage, and then inserting a separate ammeter and adjusting the power supply to match the original voltage. Of course, the voltmeter must be downstream of the ammeter.
The answer to this depends on the material from which the resistance is made. For most materials resistance increases with increasing temperature. This is referred to as having a "positive temperature coefficient". Some materials have a negative temperature coefficient; these do have uses in electronics.
Nothing will happen to the resistance of the circuit. However, with the switch open, it will be 'seen' as having infinite resistance from the supply side.
Loading refers to the phenomena that occurs when a load circuit having low effective impedance is connected to a supply circuit having higher effective impedance.
Instead of having C6H12O6, you'd have C6O6. It's called cyclohexanehextone.
Yes, a superconductor has zero resistance.
The correct term is 'current', not 'amperage'. The answer is that nothing will happen to the resistance. Having said that, changing the resistance will cause current to change for a fixed value of voltage.Resistance is determined by the length, cross-sectional area, and resistivity of a material. Resistivity is affected by temperature, so resistance is also therefore indirectly affected by temperature. Only by changing one of these variables will the resistance change.Since the ratio of voltage to current will tell us what the resistance of a circuit happens to be (it's not affected by that ratio) for a particular ratio, the ratio will increase (as per your question) if the resistance increases. But it's not the ratio that's affecting resistance, its the resistance affecting the ratio!
electroscope
Having a diversity of species and having resistance towards change
The correct term is 'current', not 'amperage'. The answer is that nothing will happen to the resistance. Having said that, changing the resistance will cause current to change for a fixed value of voltage.Resistance is determined by the length, cross-sectional area, and resistivity of a material. Resistivity is affected by temperature, so resistance is also therefore indirectly affected by temperature. Only by changing one of these variables will the resistance change.Since the ratio of voltage to current will tell us what the resistance of a circuit happens to be (it's not affected by that ratio) for a particular ratio, the ratio will increase (as per your question) if the resistance increases. But it's not the ratio that's affecting resistance, its the resistance affecting the ratio!
Absolutely the more Resistance is put in series the less current Will flow.
Unprotected steel is generally not recognized as having a fire resistance rating.
A tunnel diode.
Assuming you're referring to a simple incandescent bulb . . .When the bulb burns out, the filament is open, and it is electrically no longer there.The voltmeter is then across the battery, which is open circuited, i.e. without a load.The meter measures the open-circuit voltage of the battery, nominally 6 V.