No, 277 volts is the line to neutral of a 480 volt wye three phase system. L1- N, L2 - N and L3 - N will give you 277 volts. L1 to L2. L2 to L3 and L3 to L1 will give you 480 volts.
A voltage of 277 is the line to neutral (ground) voltage of a 480 volt wye three phase system. L1- N, L2 - N and L3 - N will give you 277 volts. L1 to L2. L2 to L3 and L3 to L1 will give you 480 volts.
It is a type of electricity supply that gives 120 v between each phase wire and neutral, that can be used for 120 v low-power circuits in a building.Yes 208 voltage is part of a three phase system. It is a three phase wye connection producing 120/280 voltages. L1 - L2, L2 - L3, L3 - L1 are the 208 voltage legs and L1 - N, L2 - N, L3 - N are the 120 volt legs.
The red and black wires are Line wires in a 3 wire service and includes a common (neutral) wire.
if it is a 240volt motor it does not matter,
The proper terminology is L1,L2,N. N is for neutral and it is this wire that is grounded. The 120 voltage is already there to use in a residential system. The voltage measurement from the L1 to N will give you 120 volts. Also from L2 to N will give you 120 volts and as you know from L1 to L2 will give you 240 volts. Single pole breakers in the panel board starting at the top, alternate between L1 and L2 all the way down to the bottom. These breakers all have 120 volt outputs. If you plug a 2 pole breaker into two slots then you get 240 outputs because L1 and L2 are adjacent to one another.
L1 is black or the hot wire and L2 is white or the netural wire
Answer for USA, Canada and countries running a 60 Hz supply service.A three wire system uses two lines L1 and L2 and a Neutral. You can obtain a 120 volt potential from L1 to N or 120 volt potential from L2 to N. Between L1 and L2 you can obtain a potential of 240 volts.
In most circumstances and electrical schematics L1 is black and L2 is white. L1 is usually the "hot" wire and L2 is the "neutral".
No, 277 volts is the line to neutral of a 480 volt wye three phase system. L1- N, L2 - N and L3 - N will give you 277 volts. L1 to L2. L2 to L3 and L3 to L1 will give you 480 volts.
From a three phase four wire distribution system the voltages would be as follows. From L1 to N - 277 volts. From L2 to N - 277 volts. From L3 to N - 277 volts. From L1 to L2 - 480 volts. From L2 to L3 - 480 volts. From L3 to L1 -480 volts.
A voltage of 277 is the line to neutral (ground) voltage of a 480 volt wye three phase system. L1- N, L2 - N and L3 - N will give you 277 volts. L1 to L2. L2 to L3 and L3 to L1 will give you 480 volts.
In North America 120/240 is the main voltages used. It is known as a three wire system. L1 to L2 supplies 240 volts. L1 to N supplies 120 volts and L2 to N supplies 120 volts.
It is a type of electricity supply that gives 120 v between each phase wire and neutral, that can be used for 120 v low-power circuits in a building.Yes 208 voltage is part of a three phase system. It is a three phase wye connection producing 120/280 voltages. L1 - L2, L2 - L3, L3 - L1 are the 208 voltage legs and L1 - N, L2 - N, L3 - N are the 120 volt legs.
On the motherboard.
The red and black wires are Line wires in a 3 wire service and includes a common (neutral) wire.
If the motor wire numbers are L1, L2 and L3, it is not a single phase motor. It is a three phase motor. Also for future reference, a 220 volt single phase motor does not use a neutral.