0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Picture of belt diagram for troy bilt pony?
Have not seen picture of belt for troybilt riding mower(deck ) my problem is when I disengage blades,it does not have enough slack and blades keep turning
Why do the blades on your lawnmower keep turning when its out of gear?
It is due to the momentum still in the blades.
Why does your lawnmower make a rasping sound when the blade stops?
What you are probably hearing is the little "brake pad" (for lack of a better term) that the blade pulley rubs against to stop it from turning. The belt always turns. So without something to keep the blades from turning they would never stop.
Are hidden blades illegal if you don't keep them hidden?
Hidden blades are illegal anywhere you go becuase they can be classified as a spring-assisted blade, which is against the Switch-blade Act.
How do you change blades on a cub cadet 1045?
You need to remove the deck according to the directions in the manual. Once the deck is off the machine flip it over and use a 2x4 to keep the blade from turning. Then you a socket to loosen the nut. Put your new blades on a torque to specs. (I think it is 70 ft lbs).
How to Install New Wiper Blades on a Vehicle?
It's important to keep the wiper blades on a vehicle in good condition. Wiper blades can remove debris, improve visibility, and aid with snow removal during the winter. An older set of wiper blades can cause several problems: old wiper blades can leave streak marks, scratch glass, and can damage a wiper blade motor. The following guide provides simple tips to install a new set of wiper blades.Measure the existing wiper blades installed on a vehicle. It's important to measure only the rubber part of a wiper blade. Wiper blade measurements are based on the length of the blade that comes in contact with the vehicle's glass. Never install a wiper blade that is too large for a vehicle. This can put excessive strain on a wiper blade's motor.Old wiper blades are simple to remove. Lift the old wiper blades directly away from the windscreen. They should pivot on a 90 degree angle from the base of the blade. The back side of the wiper blade will have a small hinge attached by a spring. Lifting this hinge will allow the old wiper blade to be removed. Most blades will slide out of a slot after the hinge is removed.A new wiper blade should be installed the same way the old blade was removed. Slide the new wiper blade into the empty wiper blade slot. Attach the hinge assembly to the mirror using the spring latch. This will help ensure that the wiper blade can't move. Push the wiper blade back towards the vehicle, and test to make sure that it is securely in place. Never operate an improperly installed wiper blade -- this can result in wiper blade motor damage, windscreen scratches, and a damaged wiper blade assembly.Make sure to recycle old wiper blades when finished. Wiper blades are usually made from aluminum and rubber. Some auto repair shops will pay to recycle old wiper blades. This can be a great way to help the environment while saving money.
How do you increase wiper blade life?
The number one enemy of wiper blades is direct sunlight and heat which dry-rots the rubber. So, keep them out of sunlight. Of course, keep glass clean. Wipe down rubber blades. See sources and related links below for more information.
Why do some helicopters have more than 4 blades?
The number of blades required is proportional to the amount of lift required. There are several factors that affect the amount of lift produced by rotor blades. They are the shape of the air foil, the rotational speed, the angle of attack, the length of the rotor blades, and the strength of the blades. All of these have practical limits. Adding an additional blade helps keep all these parameters within practical limits.
What does Gandalf say about the blades?
When Gandalf and the Dwarves find the blades in the cave, the Wizard tells Thorin they're made by the Elves. When the Dward is about to throw them to the ground, unwilling to wield a weapon made by the Elves, Gandalf tells him he couldn't wish for a better blade, convincing him to keep it.
Why do helicopters have a difficult time flying at altitudes above 6000 m?
A helicopter blade works the same way as a wing on a fixed wing aircraft. The air flowing faster over the top of the airfoil generates lift. When a helicopter flies at a high altitude the air gets thinner. Because the air is thinner, more pitch on the blades is needed to keep the helicopter in the air. When too much pitch is on the blades the blades stall, air moves past the bottom of the blade and creates a vortex behind the top of the blade. All lift is lost and you lose altitude.
How do you remove your lawn mower blades from my John Deere lawn tractor?
simply remove the bolts that hold the blades to the mower.check and make a note of the blades positions/there's an 'up' and 'down'-[ 'down' faces the lawn] put something,-ratchet handle, 2x4- to keep the blade[s[ from turning and remove the retaining bolt[s]replace the new blade[s] facing the proper direction-if in doubt,ask a dealer-they may laugh,but it's importent. hope this helps. It would help more if I knew which direction the bolts turn, reverse or normal on a twin blade 38" deck? I believe the size head for the bolt is a 5/8 socket, you will probably need a cheater bar for leverage to help get the bolt loose from the blade spindle. Or a hammer to tap the handle of socket. Make sure you lube the spindles when putting things back together. The lube points are on top of deck around the 3 spindles on most decks !
How does shoulder blades help animals?
shoulder blades on an animal are very important! they keep the animal in place!
