0
It means you have effectively no resistance to current flow. Whether this is good or not depends on whether you WANT resistance to current flow.
If you're testing a length of wire, a cable, or something like that, having your ohmmeter read zero would be good.
If you're testing a motor or something else that needs to have resistance to work, having your ohmmeter read zero is bad and is called a Short Circuit.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How do you take care of an ohmmeter?
Never connect the ohmmeter's leads across a voltage.On an analog meter, adjust the zero before use.Turn your ohmmeter off when not in use, to protect against voltage drain.When your ohmmeter's battery is low, or your meter won't be used for a while, remove the battery to prevent damage to the meter from battery leakage.
When testing for electrolysis in the cooling system the digital volt-ohmmeter (DVOM) reading should not exceed?
Go
What tool can be used to test for electrical conductivity?
The easiest way is to use an Ohmmeter. This function is usually built into most multimeter that can be bought at any hardware store. An Ohmmeter measures the electrical resistance of a material. The lower the number the more conductive that material is. If the Ohm reading is above the maximum reading on the meter then their is infinite resistance which means that the material is not a conductor of electricity.
Which wire is ground on harley Davidson 3 prong headlamp connector plug?
I'm not at all qualified in electronics but I would use an ordinary ohmmeter. Put one lead to a bare metal part of the bike and touch the other lead to each of the three prongs of the headlite. one of them should show zero resistance and that one should be ground. (I think!)
Is absolute zero is equal to -273 degrees on the Kelvin scale?
Kelvin is defined in such a way that absolute zero is zero Kelvin.Kelvin is defined in such a way that absolute zero is zero Kelvin.Kelvin is defined in such a way that absolute zero is zero Kelvin.Kelvin is defined in such a way that absolute zero is zero Kelvin.
What should the ohmmeter read when the lead probes are touched together?
When the lead probes of an ohmmeter are touched together, the ohmmeter should read close to zero ohms, indicating a short circuit or very low resistance between the probes.
How do you take care of an ohmmeter?
Never connect the ohmmeter's leads across a voltage.On an analog meter, adjust the zero before use.Turn your ohmmeter off when not in use, to protect against voltage drain.When your ohmmeter's battery is low, or your meter won't be used for a while, remove the battery to prevent damage to the meter from battery leakage.
What value will appear on ohmmeter when we will check 100 uh microhenry inductor?
The reading will be very close to zero ohms.
At which end of the ohms scale are resistance measurement more reliable the zero end or the infinity end?
On an analog ohmmeter, measurements are more precise and more accurate at the zero end of the scale.
What an ohmmeter measures?
resistance to current flowAn ohmmeter meassures resistance
A zero reading on an ohmmeter means the circuit or component is open is this true or false?
This is false. A zero reading is what you get when you press the probes of themeter together with nothing between them, to make sure the meter is working.That's about as closed as the circuit under test can get.
Is a ohmmeter a pressure gauge?
No. An Ohmmeter measures electrical resistance to the flow of current.
What is the configuration of the ohmmeter?
An ohmmeter is connected in parallel to a resistor. Be sure that there is no power in the circuit when testing.
Should the ohmmeter be connected to the circuit while the power is being applied or only when the circuit is turned off?
Turn off the supply before using the ohmmeter,it will damaged your ohmmeter when supply is present.
What is ohmmeter?
An ohmmeter is a type of electrical metre that measures electrical resistance. When in resistance-measuring mode, multimeters also operate as ohmmeters. An ohmmeter measures the resistance of a circuit or component by passing electricity through it.
How do you test blower motor resistor on a 1994 Toyota pick-up?
Remove and test with an ohmmeter Explain how to test with an ohmmeter?
What is the function Ohmmeter?
What is the function of rheostat
