You obviously do not know what you are doing. Electricity is DANGEROUS and you can kill yourself with it. If something electric in your house needs testing or fixing, employ the services of a qualified electrician to do it for you, DO NOT TRY AND DO IT YOURSELF.
You obviously do not know what you are doing. Electricity is DANGEROUS and you can kill yourself with it. If something electric in your house needs testing or fixing, employ the services of a qualified electrician to do it for you, DO NOT TRY AND DO IT YOURSELF.
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
Wattage (power) is not stored in a breaker; in its tripped position, electrical power form the power line is disconnected. When the breaker is activated, electricity (power) flows through the breaker to the circuit in the home. Using the formula below, you can find the wattage the breaker can handle, not how much it has. Watts = Volts x Amps = 120 volts x 15 amps = 1800 watts A toaster requires 1500 watts of power, so if you are running a coffee maker which probably requires 700 watts or more and turn on you toaster, that 15 amp breaker will trip.
Turn the power off to that plug at the breaker. If at that point you can still get at the broken parts remove them. If not, then replace the plug.
There are only two conditions that cause a breaker to trip. An overload condition of the connected load is one cause. To cause an overload condition on a breaker that supplies a garbage disposal, the motor in the unit would have to be jammed. Turn the breaker off and see if you can turn the blades in the unit. This might have to be done from the under side, look for the motors cooling fan on the bottom of the motor and see if you can turn it. If the breaker trips instantaneously when the unit is turned on, then there could be a wire grounding in the motor junction box. Same scenario, turn the breaker off, open the junction box and look for wiring problem. Use your power of smell, it is a fine diagnostic tool when it comes to burnt electrical equipment.
You obviously do not know what you are doing. Electricity is DANGEROUS and you can kill yourself with it. If something electric in your house needs testing or fixing, employ the services of a qualified electrician to do it for you, DO NOT TRY AND DO IT YOURSELF.
you don't you turn off the power in rodricks room with the joshie card and the breaker
No. Power to all the circuit breakers will be cut off except for the Main power breaker. The Main power breaker (which supplies power to all other breakers and will say 100, or whatever your max breaker box power is, on it )will have power going to it all the time, unless power is turned off outside the house.
Check your fuse block or circuit breaker first, then turn wiper switch on and check for power at wiper motor, if the fuse/breaker is ok and you have power to motor, motor may be seized. listen for humming from motor, if none of above follow tech manual for testing wiper switch,or short to ground
It is safer to find out why the breaker tripped before the power is turned on. Turn off all equipment, then turn on the supply, then turn on each appliance one by one to find the culprit.
Turn the power off and call an electrician.
If your cable box won't turn on after a power outage, there may have been a power spike that tripped the breaker inside the box. Look for a reset button on the back of the box, check the owner's manual, or contact your cable company for help in resetting the breaker.
You need to turn off the power at the circuit breaker.
turn breaker off. unhook thermostat wire to furnace turn breaker on. worth a try; if it works you will have to turn off breaker to shut it down.
Parallel circuit.
If the Shop Vac is tripping the breaker to a house turn other electronics off while it is in use. The power in the house should be checked out by a electrician.
There is a thermostat somewhere, usually on the wall or on the heater itself. Just turn the breaker off at the breaker box. Label the breaker if it is not already labeled. Once the power is turned off to the unit, you can disconnect the wires inside the heater to permanantly shut down the unit.