Spark Plugs and Wires

Where are the spark plugs and plug wires in a 2002 mustang gt and how do you change them?

232425

Top Answer
User Avatar
Wiki User
2005-11-12 06:21:32
2005-11-12 06:21:32

raise the hood and look at the top of the heads the wires go into the center of the valve covers on the 4.6 like a hemi not on the sides like a 5.0 use an air compressor to blow out any trash around the plug before you remove it or the trash may fall into your cylinders!!! thin wall socket and long extension.Use a piece of small hose to attach to wire side of plugs to start them to keep from crossthreading them.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Change the spark plugs and wires... Change the spark plugs and wires...

User Avatar

Disconnect the battery, remove the spark plugs wires and boots and remove the spark plugs. Put in the spark plugs, replace the spark plug wires and boots, and connect the battery.

User Avatar

No you do not need to replace any plugs at all when replacing wires.

User Avatar

at the end of those black wires.....

User Avatar

we need help! how do you change spark plugs and wires on a 2001 toyta camery

User Avatar

how do you change spark plugs and wires on 2002 land rover discovery

User Avatar

Disconnect the battery, remove the spark plug wires and boots, and remove the old spark plugs. Toss out the old spark plugs, put in the new spark plugs, replace the spark plug wires and boots, and connect the battery.

User Avatar

remove the spark plug wires one at a time and unscrew the plugs

User Avatar

Pull the spark plug wires off the spark plugs. Remove the spark plugs with a spark plug socket. Install the new spark plugs and put the spark plug wires back on. I recomend replacing the spark plug wires as well. If replacing them, just remember that the new wires are hooked up the same ways that the old ones came off.

User Avatar

No. However, newer plug wires can be extremely difficult to remove without damaging them.

User Avatar

Disconnect the battery, remove the engine cover, remove the spark plugs wires and boots, and remove the spark plugs. Put in the new spark plugs, replace the spark plug wires and boots, replace the engine cover, and connect the battery.

User Avatar

Disconnect the battery, remove the spark plug wires and covers, and remove the old spark plugs. Next, put in the new spark plugs, attach the covers and spark plug wires and reconnect the battery.

User Avatar

Remove the spark plug wires. Turn the spark plugs to the left with a deep well 5/8 socket. The spark plugs will come out. Reverse the process with the new spark plugs.

User Avatar

To change the spark plugs on a Maruti Alto, first, make sure the car is turned off and parked safely. Find the spark plugs at the end of the rubber-like wires in the engine. Remove the wire from the spark plus, remove the old spark plugs, and put in the new ones, and replace the wires.

User Avatar

Disconnect the battery, remove the spark plug wires and boots, and remove the old spark plugs. Dispose to the old plugs, put in the new spark plugs, replace the spark plug wires and boots, and connect the battery.

User Avatar

The main reason a car misfires is because the spark plug wires are not installed correctly. Check the car's firing order to ensure the spark plug wires running from the distributor cap to the spark plugs (in the cylinders) are in the right order. One or more spark plugs could be damaged or worn so the firing order is correct, but the spark plugs are not sparking into the spark plug wires to ignite the engine.

User Avatar

There is no plug wires on a J30, you just unbolt the coil pack that's on top of the spark plugs and then change your plugs, after your finnished changeing the plugs you just reinstall all the coil packs on top of the spark plugs, but becarefull you don't break any of your coil packs, they will cost you.

User Avatar

Disconnect the battery, remove the spark plug wires and boot covers and remove the old spark plugs. Put in the new spark plugs, leave the correct gap size, replace the boot covers and wires and connect the battery.

User Avatar

How can I change the wiring and spark plugs on my 1996 Cadillac Sedan Deville Concours?

User Avatar

Remove the spark plug wires from the spark plugs, use an extension for your Allen wrench, and use a spark plug socket to remove the spark plug.

User Avatar

Replacing Spark Plug High Voltage WiresNO, not necessarily. Spark plug wires only need to be replaced maybe once or twice in the life of a vehicle, IF THEY HAVE NOT BEEN PHYSICALLY DAMAGED OR ABUSED.Therefore, it is normally not necessary to replace the plug wires when replacing the plugs.

User Avatar

To change spark plugs on a 5.9 2002 Dodge Ram 1500, locate the old spark plugs. These are located at the end of the 8 wires inside the vehicle's bonnet. Remove the old spark plugs and replace with new.

User Avatar

Disconnect the wires to the battery, remove the spark plug cables and boot covers, and remove the old spark plugs. Next, put in the new spark plugs, attach the boot covers and spark plug cables and reconnect the wires to the battery posts.

User Avatar

Changing spark plugs is pretty simple. Disconnect the battery, remove the wires to the spark plugs from their location, remove the old spark plugs, put in the new spark plugs, plug the cables to the right spark plug and reconnect the battery.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.