0
What else can I help you with?
What is the replacement spark plug for a Torch A6RTC?
One I know of is NGK CR6HSA
How do you change the spark plug wires?
Get the proper replacement wires. One end goes on the spark plug and the other goes on the distributor cap. They are connected to the distributor cap in order,so do not place one out of sync.
Where can one purchase Autolite spark plugs?
One can purchase an Autolite spark plug from a local store that carries Autolite products. One can use the store locator on the official Autolite website to find a location near him or her.
What causes a random misfire on a Vw bora 1999 engine code APK Intermittent fault that requires replacement of cylinder 4 spark plug.?
Hi I had the same fault on my golf 2l apk and after spark plags replacement it solve the problem. as i been told the cause is one spark plug has a leak . Moshe Keren
How do you change spark plugs on a 1996 Toyota Tacoma?
I've done it a few times on my 1996 Tacoma 2.4L engine. You need a 5/8" spark plug socket (3/8" drive preferably) with the foam rubber insert that holds the spark plug once it's loose. And a ratchet and extension (12" is enough I think). Then, one by one (for each spark plug), remove the spark plug wire, use the ratchet/extension/socket to remove the spark plug, reverse the process to install the new spark plug. One thing I ran into this last time was that the foam rubber insert in the spark plug socket held the spark plug more tightly than the socket was held on the end of the extension (it was a brand-new spark plug socket), so I had to back that first one out and only very gently push the replacement spark plug into the spark plug socket so the foam rubber insert barely held it enough to lower it down into the hole for the spark plug (through the valve cover).
How do you change the sparkplugs on a Toyota Tacoma 4-cylinder?
I've done it a few times on my 1996 Tacoma 2.4L engine. You need a 5/8" spark plug socket (3/8" drive preferably) with the foam rubber insert that holds the spark plug once it's loose. And a ratchet and extension (12" is enough I think). Then, one by one (for each spark plug), remove the spark plug wire, use the ratchet/extension/socket to remove the spark plug, reverse the process to install the new spark plug. One thing I ran into this last time was that the foam rubber insert in the spark plug socket held the spark plug more tightly than the socket was held on the end of the extension (it was a brand-new spark plug socket), so I had to back that first one out and only very gently push the replacement spark plug into the spark plug socket so the foam rubber insert barely held it enough to lower it down into the hole for the spark plug (through the valve cover).
What would cause one spark plug wire to arc to the engine at the spark plug boot?
bad spark plug wire.
How do you fix a spark plug?
only way to fix a spark plug is to replace the problem plug with a new one
No spark to one of the spark plugs?
Check the plug and the wire.
How do you change the spark plugs in a 1987 Chevy Celebrity?
To change the spark plugs in a Chevy Celebrity: 1. Give the spark plug boot a twist to free it up from the spark plug, then pull on the boot to remove the spark plug wire from the spark plug. 2. Use a 5/8" spark plug socket with an extension and ratchet or breaker bar to loosen then remove the spark plug. 3. Set the gap on the new plug to .045" then screw it back into the spark plug hole in the head. Tighten the spark plug and replace the spark plug wire. I change the spark plugs one at a time to keep from getting the spark plug wires on the wrong spark plug.
What does it mean when 1 plug out of 8 is wet?
Probably losing spark in that one cylinder, maybe a faulty spark plug, a spark plug wire or distributor cap.
How do you check plug wires?
How to Check a Car's Spark Plug Wires By eHow Cars Editor Part of car overhaul and car maintenance is checking your car's spark plug wires. These cables connect the spark plug to the distributor. You must check them every year and replace or clean them as needed. Always replace the entire set even if only one wire shows signs of wear. Difficulty: Moderately Easy 1. Turn off your car engine to overhaul your spark plug wires. Let your car cool down. Open the hood of your car and look inside for your spark plug wires. 2. Find the distributor. You will see several cables going across and ending at the individual spark plugs. These are the spark plug wires. 3. Remove one spark plug wire at a time for better inspection. Pop it off the spark plug and the distributor. Remove only one wire at a time. This will ensure you do not mix up the spark plug wires. 4. Look at the wire carefully. If it has any tears or cracks, you must replace it now. Always replace all spark plug wires at the same time even if only one needs replacement. 5. Clean a dirty spark plug wire. Use hand cleaner soap and wipe completely dry. Reinstall the spark plug wire into the distributor and connect to the spark plug. 6.Repeat this overhaul at least once a year. Remember to check the spark plug wires when you change your spark plugs. Tips & Warnings · Do not remove all of the spark plug wires at one time unless you are very sure you know which one goes where. If you mix them up, your car will not run. Remove one at a time then replace or reinstall it. Move on to the next one.
