answersLogoWhite

0

In a flashlight. You have a power supply (the battery), a load (the bulb),

and a switch to prevent current in the loop when you don't need light.

It couldn't be any simpler, unless you eliminate the switch and let the

light shine for as long as the battery survives.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

Where could you find a circuit?

i


Where could I find your main circuit breaker and a siemen panel?

The main circuit breaker is typically mounted to the meter base, and is usually outside, where the electrical service comes into the house. Siemens is a large manufacturer of electrical components. You should be able to find Siemens equipment at several electrical supply wholesalers in your area. Note that many of the electrical wholesalers will NOT sell to the public; you may need to find an electrician or other contractor to purchase Siemens equipment.


Where can you find the layout of the fuze box for Skoda octavia?

look in the manual it in the electrical part of the book. If you have a RHD car it could be reversed watch out. remember when you change the fuse use the same colour as this is the correct rating for the circuit, if it is to low it will keep blowing and you will need to replace it or if it to high you could cause a electrical fire if ther was a fault on the circuit. hop this helps


Where circuit breaker are used?

Circuit breakers do not use anything, they are a controlling device. They can automatically open the circuit if the current exceeds the current rating and you can manually disconnect the power from the circuit.


Where to find a circuit?

Circuit breakers can be found in any circuit breaker panel. New circuit breakers can be bought at any shop that sells parts for installing or repairing electrical wiring circuits.


To find the current in a complex circuit it is necessary to know?

the source voltage and the total impedanceAnswerA 'complex circuit' describes a category of circuit that is neither series, parallel, nor series-parallel. A relatively-simple example of a complex circuit is a Wheatstone Bridge. You cannot analyse or resolve a complex circuit using the techniques used to analyse and resolve series, parallel, or series-parallel circuit. Instead you must use one or other of the various electrical theorems. For example, to determine the currents flowing in a Wheatstone Bridge circuit, you could use Kirchhoff's Laws or Thevenin's Theorem.


Which circuit could you find Virage de lecole sweep?

circuit paul ricard


What type of material will you find outside of an electrical circuit to protect it?

You will typically find materials like insulation, enclosures, and grounding systems outside of an electrical circuit to protect it from environmental factors, physical damage, and electrical hazards. These materials help to ensure the safety and functionality of the electrical system.


How to find the neutral wire in an electrical circuit?

To find the neutral wire in an electrical circuit, you can use a voltage tester or a multimeter. Turn off the power to the circuit, then test each wire to see which one has a voltage reading close to zero. This wire is the neutral wire. Remember to always follow safety precautions when working with electricity.


How can I determine how to find a neutral wire in an electrical circuit?

To find a neutral wire in an electrical circuit, you can use a voltage tester or a multimeter. Turn off the power to the circuit, then test each wire to see which one has a voltage close to zero. This wire is likely the neutral wire. Be sure to follow safety precautions when working with electricity.


How can I find a 4-way switch wiring schematic to properly install a 4-way switch in my electrical circuit?

You can find a 4-way switch wiring schematic by searching online or consulting an electrical wiring guide. This will help you understand the proper connections and installation steps for adding a 4-way switch to your electrical circuit.


What is a simple circuit?

A simple circuit is a circuit containing one voltage or current source in series with, or in parallel with, one load.Since it is a simple circuit, both definitions, series and parallel, are equivalent and mean the same thing.well ist a circut that only has one wire and if one power outlet goes out so do the rest and as you can read i can't really find out i was tring to find out and thats not simple because im a 10 year old in 5th grade! (advanced 5th grade)