Chevy Corvette
Home Electricity
New Electrical Work
Modification of Old Electrical Work

Where does the wire coming off EGR switch connect for a 1988 Corvette and where can you find a picture?

616263

Top Answer
User Avatar
Wiki User
2006-02-10 06:16:35
2006-02-10 06:16:35

Here is a link that should help. It is for a 87 Vette which should be the same. www.corvetteforum.net/c4/john_robatto/index5.shtml It shows the connector at the rear of the engine below the plenum. Look at illustration 8A2010.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Yes, it's possible. Connect the wire coming from the switch in the internet port in the router.

User Avatar

How do I change the dimmer switch on my 1993 corvette?

User Avatar

I am not a corvette mechanic, but I call BS on vacuum diagnostic switch.

User Avatar

There are at least two ways. First, you connect the wireless router directly to the cable modem, and then the switch in the wireless router. You have to connect the cable coming from the modem in the wireless router internet port. Second, you connect the wireless router to the switch, again the cable coming from the switch you have to connect on the wireless router internet port. It's better to put the wireless router just after the modem, but it's not required.

User Avatar

Purchase a 16 port switch and connect the utp cable coming from the ISP to the uplink terminal of the switch. Now connect each individual notebook to switch using the UTP cable and leave the IP address to be assigned by DHCP

User Avatar

= Where is the fuel pump reset switch on a 1989 corvette automatic? =

User Avatar

If the switch has a black screw this is a 3way switch. On a 3way circuit on one switch you connect the black power wire to the black screw, and on the other end of the 3way circuit on the other switch you connect the black wire coming from the light to the black screw.

User Avatar

Remove the retaining ring from the top of your 1989 Chevy Corvette ignition switch. Slide the ignition switch out and remove the wiring harness.

User Avatar

How do I connect a wall light switch that has 3 terminals, the third being for the ground wire. Which terminal should be connected to power coming from the breaker box?

User Avatar

The factory security system does not have a valet switch.

User Avatar

can you connect wireless modem to a switch which will to two routers

User Avatar

Basically you need to connect the black supply wire directly to the outlet rather than have it go through switch. You can have two possible conditions. The first condition is that the supply comes to the switch box and connects to one side of the switch. The other side of the switch goes to the outlet. In this case just remove each black wire from the switch and connect them together with a wirenut. If the black supply wire goes to the outlet and there is another black wire going to the switch then there will also be a wire coming back from the switch. Just disconnect the wire coming from the switch to the outlet and connect the black supply wire directly to the outlet.

User Avatar

Install the switch in the wall outlet box you have installed. Now run a 12/2 or 14/2 wire from the switch to the light fixture in the ceiling. Run the exact same size wire that is already powering the light. Connect the ground wire coming from the light switch to the ground wires in the ceiling box. At the light in the ceiling cut the black wire powering the light. Cut only that wire. Now strip the 2 black wires back and connect the white wire coming from the wall switch to one of the black wires and the black wire coming from the wall switch to the other black wire. At the wall switch connect the ground wire to the ground screw on the single pole switch. Now connect the white and black wire to either screw. Does not matter which one. Now when you turn the switch off you are breaking the flow of electricity to the light. This is called a switch leg.

User Avatar

To connect a PC to a switch you should use a straight through UTP cable.

User Avatar

the straight cable can connect switch with router

User Avatar

with your power coming into the switch, you connect the neutral wire (white) to the other white wire that is going to the lights. then the 2 black wires go onto the switch. now that you have the light switched, you just connect the other lights to the first one

User Avatar

there is not an inertia switch on a corvette, or for that matter any Chevrolet product. I am an ase master and have been with gm for 16 years.

User Avatar

How do I replace the power window switch on 1977 Corvette coupe

User Avatar

The 1995 Chevrolet Corvette on relay switch can be found in the fuse box. The horn relay switch will be in the third column, second from the top.

User Avatar

Turn the breaker off sending power to this circuit. Just run power from the outlet up to the light switch box using a 12/2 or 14/2 wire. Now run a 12/2 or 14/2 wire from the light switch box up to the light. In the light switch box tie all the white wires together and push them in the back of the box. Connect all the ground wires together and connect that to the green screw on the light switch. Connect the black wire coming from the outlet to one of the screws on the light switch. Now connect the black wire coming from the light to the other screw on the light switch. Turn your breaker back on and this will control your lite.

User Avatar

If I am correct I think you are wanting to know how to connect a 3 way switch where you can turn off an light at 2 locations. At one switch you run a 12/2 wire from the switch to the light. There is no power at this switch. At the other switch you have your a power input wire. Run a 12/3 wire from one switch to the other. Connect all the whites together and shove them back in the box at the switch with the wire going to the light. At the switch with the 12/2 wire going to the light, connect the black 12/2 wire coming from the light to the black screw on the 3way switch. Now connect the red wire and black wire from the wire you ran between the switches to the other 2 screws on the switch. It does not matter which you connect to which screws. Connect the ground wire and put that switch in the wall with the cover on it. Now move the the other 3way switch with the power wire. Again connect all the whites together and shove them back in the box. Connect the black wire from the power source to the black screw on the switch. Now connect the other 2 wires left, black & red to the other 2 screws that are left. Again it matters not which wire you connect to which 2 screws that are left. Connect your ground wire and put the switch in the wall a cover on. At the light connect the black to black and white to white. Connect the ground wire to the green or ground wire on the light. You are done.

User Avatar

Why is gasoline coming out of the ignition switch?

User Avatar

Connect a wire from each PC to an unused port on the switch.

User Avatar

You connect up to 5 devices with HDMI cables to the switch, and connect the switch output to your TV with another HDMI cable. You the selector switch or the remote to go between the devices.

User Avatar

Yes you can connect two or more switches together You need a crossover cable in order to accurately connect them though.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.