0
What else can I help you with?
What is the firing order for a 2005 suzuki forenza?
on the coils from back to front it is 1423 for plug wire location
How do you remove a 2005 Suzuki Forenza headlamp after disconnecting wire harness?
You remove a few bolts to remove the entire headlight assembly. There is a video on YouTube on exactly this. Do a search for Forenza Replace.
Where is the tach signal wire for a 2005 Hyundai tiburon?
The tach signal wire for a 2005 Hyundai Tiburon is typically located at the engine's ignition system. You'll find it on the ignition coil, where it sends a signal to the engine control unit (ECU). It's usually a green wire, but it's best to consult a wiring diagram for precise identification. Always ensure the vehicle is turned off and disconnected from the battery before working on electrical components.
Where can you get a 2005 Pontiac sunfire radio wire harness diagram?
the dealership for that brand of car
86 Ford Ranger fuel tank sending unit wire diagram?
The fuel tank sending unit in an '86 Ford Ranger typically includes a few key wires: a ground wire, a signal wire that sends fuel level information to the gauge, and sometimes a power wire for the fuel pump (if applicable). The ground wire is usually black, the signal wire is often light green or gray, and the power wire can vary by model. For an accurate wire diagram, it is recommended to refer to the vehicle's service manual or a dedicated wiring diagram resource specific to the 1986 Ford Ranger.
Why did both headlights go out on your 2005 suzuki forenza?
what has happend is a wire has melted behind the cluster causing the low beams not to function recomend to take to your suzuki dealer to have repaired the wires are hard to get to and may be cover under by suzuki because it is a problem for these cars all forenza's
What color wire supplies power to the left turn signal?
The color of the wire that supplies power to the left turn signal can vary depending on the vehicle's make and model. However, in many automotive wiring systems, the left turn signal wire is commonly green or yellow. Always refer to the specific vehicle's wiring diagram for accurate information.
Wiring diagram for a o2 sensor for a 2004 silverado 4.8L?
For a 2004 Chevrolet Silverado with a 4.8L engine, the O2 sensor wiring typically includes a heater wire, a signal wire, and a ground wire. The upstream O2 sensor generally has a white wire (heater), a black wire (signal), and a gray wire (ground). The downstream sensor will have similar wiring, often identified by different colors. Always refer to a specific service manual or wiring diagram for accurate pin configurations and color codes for your vehicle.
How do you wire a signal stat 900?
The wiring diagram can be found on this website as a pdf file. It shows several signal-stat devices including the 900.Link is:http://m37.crwdesigns.com/diagrams.htm
Where do you hook up the wire on an aftermarket tachometer on an 87 jetta mark 2?
DISCLAIMER: I am not responsible for your actions You need an ECU diagram of your vehicle. Find the correct pin # and find the wire that attaches to it. Use a wire tap and run that wire as the signal wire to your new tach
How do you determine the signal wire in a 4 wire oxygen sensor?
To determine the signal wire in a 4-wire oxygen sensor, first identify the wires by their functions: typically, the sensor will have two wires for heating (heater wires), one for the signal (usually a smaller gauge wire), and one for ground. You can use a multimeter to measure resistance; the heater wires usually have low resistance, while the signal wire should show higher resistance. Additionally, consult the specific vehicle's wiring diagram or service manual for the correct wire color codes associated with the oxygen sensor.
What is the 4 wire security camera wiring diagram for installation and setup?
The 4 wire security camera wiring diagram for installation and setup typically includes connecting the power supply wires, video signal wire, and ground wire to the corresponding terminals on the camera and monitoring system. It is important to follow the manufacturer's instructions carefully to ensure proper installation and functionality.
