0
The number 1 position on the distributor cap of a Ford 5.0 liter / 302 is :
It faces to the REAR and towards the number 7 engine cylinder ( in every
picture I have seen in repair manuals )
The engine cylinder locations are numbered :
firewall
4 - 8
3 - 7
2 - 6
1 - 5
front of vehicle
What else can I help you with?
How much is a distributor cap and rotor?
The cost of a distributor cap and rotor can vary widely based on the make and model of the vehicle, as well as the brand of the parts. On average, you can expect to pay between $30 to $100 for the distributor cap and $15 to $50 for the rotor. Labor costs for installation can add an additional $50 to $100, depending on the mechanic's rates. Always check with local auto parts stores or online retailers for specific pricing.
How do you fit a thermostat in a Daewoo matiz?
drain coolant ,and you will find thermostat housing behind distributor cap ,you may find it easier to remove distributor cap for access, mark were leads connected ,undo bolts and remove thermostat,top back up with coolant no more than 50% anti freeze
How do you know if you need a distributor cap?
You can tell by looking at where the metal touches on the inside of the cap however it is generally good practice to replace it every (30-50 thousand miles)someone correct me if I'm wrong on the mileage
Where do you put anti-freeze into a 2002 ford e-150 van?
In a 2002 Ford E-150 : The thread on cap on the engine coolant reservoir is the pressure cap / radiator cap ( so with the engine cool you add antifreeze and preferably distilled water into the engine coolant reservoir ) It came from the factory with a 50 / 50 mix of distilled water and the correct type of antifreeze for the vehicle , Ford states not to exceed 60% antifreeze in the mix
Where to top up water in Ford Fiesta?
To top up the water in a Ford Fiesta, locate the coolant reservoir under the hood. It is typically a translucent plastic tank with a cap labeled for coolant or antifreeze. Ensure the engine is cool before removing the cap, then add a 50/50 mix of water and antifreeze if needed, filling it to the "MAX" line. Be sure to securely replace the cap afterward.
Where do you put in antifreeze in 2003 Explorer?
In a 2003 Ford Explorer : Into the engine coolant reservoir ( located in the engine compartment , on the passenger side ) The thread on cap is your pressure cap / radiator cap Only add when the engine is cold ( up to the cold mark on the reservoir ) * It came from the factory with a 50 / 50 mix of distilled water and the correct type of antifreeze for the vehicle , Ford states to not exceed 60% antifreeze in the mix
How do you put antifreeze in a 2004 ford explorer?
To add antifreeze to a 2004 Ford Explorer, first ensure the engine is cool. Open the hood and locate the coolant reservoir, which is typically a translucent plastic tank with a cap labeled for coolant. Remove the cap and, if necessary, add a 50/50 mixture of antifreeze and water until it reaches the "Full" line. Replace the cap securely and check for any leaks or issues before starting the engine.
Chimney Cap?
form_title= Chimney Cap form_header= Install a chimney cap easily. How old is your chimney cap?*= _ [50] What color are the vents?*= _ [50] Do you need someone to clean the chimney?*= () Yes () No
Where is the water cap located on a 1996 grand mercury marquis?
On a 1996 Mercury Grand Marquis : ( the thread on cap on your engine coolant reservoir is the pressure cap / radiator cap ) The vehicle came from the factory with a 50 / 50 mix of distilled water and GREEN antifreeze ( meeting Ford specification ESE-M97B44-A ) Besides providing freeze protection the mixture also provides CORROSION protection ( until the corrosion package in the antifreeze is " used up " ) Ford states to not let the antifreeze portion of the mixture to drop below 40 % and not to exceed 60 %
Is there a coolant reservoir on 96 ford probe 4-cylinder and how to refill coolant for it?
( Yes ) on a 1996 Ford Probe the fill for the engine coolant reservoir is located in the engine compartment , between the battery and the drivers side fender . There is a dipstick attached to the cap and with the engine cool the dipstick should indicate that the coolant level is up to the L mark Remove the cap with dipstick , wipe the dipstick clean and reinstall the cap , remove the cap again and check the coolant level . If it shows below L it came from the factory with a 50 / 50 mix of distilled water and GREEN colored antifreeze meeting Ford specification ESE-M97B44-A so you would want to add coolant
What is the percussion cap size for a Mowrey 50 cal muzzeloader?
a rifle cap.
Where do you add water and coolant on a 97 Lincoln town car?
On a 1997 Lincoln Town Car : With the engine cool , antifreeze and preferably distilled water is added to the engine coolant reservoir ( located in the engine compartment , near the firewall , on the passenger side of the engine compartment ) * The thread on cap on the reservoir is your pressure cap / radiator cap * it came from the factory with a 50 / 50 mix of distilled water and GREEN color antifreeze ( meeting Ford specification ESE-M97B44-A ) Ford states not to exceed 60% antifreeze in the mix
