on the intake
It will bolt up, but the manifolds, flywheel, wiring are different. Also the 1997 head does not have a hole in the rear for the temperature gauge sensor.
The throttle position sensor is a potentiometer.
Use a 02 socket. The 2 sensor are located in front and behind the cat.
A 1997 Jeep Wrangler uses green coolant.
A 2002 Jeep Wrangler does not have a mass airflow sensor.
Bank 1 sensor 2 is the sensor on the downstream side of the catalytic converter.
T is right beside your throttle body(onthe right if your standing in front of your jeep)
You want to look on the intake manifold on the Jeep Wrangler.
It's called a MAP sensor. But it by the air intake. It a black box on the the driver side of the air intake.
Trouble code P0138 means:O2 sensor circuit high voltage (Bank 1 Sensor 2)
The tps is not adjustable on a 2003 Jeep Wrangler.
Trouble code P0133 means:O2 sensor circuit slow responce (Bank 1 Sensor 1)
yes it will fit1997-2006
No, different bolt pattern.
No. different bolt pattern.
The correct factory tire size for a 1997 Jeep Wrangler is P205/75R15.
If by magnetic pick up you are refering to the ignition system, the cam sensor is in the distributor, and the crank sensor is in the bell housing.
as far as i know it will. YES
No. Don't waste you time.
On a 1990 Jeep Wrangler, the IAT sensor is located on the intake manifold. It is a gray, two-wire system situated on the front of the manifold.
I have a 1999 jeep wrangler and it get around 15MPG.
A 1997 Jeep Wrangler requires 6 quarts of oil for an oil change.
No, there is no fuse for the crank sensor
That is located on the back top side of the catalytic converter, right where the outlet tube leads to the muffler.
In a 1998 Jeep Wrangler, the oxygen sensor is located in the exhaust pipe. It can be found just below the junction of the exhaust manifold and the exhaust pipe.
The 40. 1997 Jeep Wrangler needs 6 quarts of oil for an oil change.
Jeep Wrangler wheel lug patterns years 1995-2006 are 5X4.5
I shouldn't, 1990 is a YJ and the 97 is a TJ.
If a 2000 Jeep Wrangler suddenly loses power in 5th gear, it might be a problem with the speed sensor on the transmission. This sensor regulates when the Jeep will shift or should shift.
Powertrain Control Module The computer on the passenger firewall, it controls all the sensors, meaning the crankcase, camshaft sensor and son on
on the upper and rear/back edge of the flywheel cover on the driver's side. 2 bolts hold it in.
1997 to i believe 2004 jeeps are pretty much the same. are models the same?? like a wrangler for wrangler?? or rubicon for rubicon?? 97-06 clips are the same..even rubicon's
No, the 95 is a YJ, and the 97 is a TJ, they shouldn't match up.
I replaced the crank sensor and the cam pick up that is under the distributor cap and still the wrangler wants to stall or back fires and bucks at 1200 to 2000 RPM when accelerating
Jeep Wrangler wheel lug patterns years 1987-2006 are 5X4.5 Jeep Wrangler wheel lug patterns years 2007-2014 are 5X5
No, a 1997 Jeep does not have an inertia or reset switch.
The Jeep Wrangler 2.5 liter engine intake air temperature sensor is located just above the exhaust manifold. The sensor will have to wires coming out of the top of it.
The life expectancy of a 1997 Jeep Wrangler Sport is 16 years. To get the full life expectancy out of a vehicle it should be properly maintained.
A throttle position sensor measures the angle of the throttle plate.
If you are getting a p0123 code on a Jeep Wrangler, it means that your throttle body sensor is not working properly. Once you replace this sensor, the code will go away and your Jeep?æwill run smoother.
Price brakes most expensive brakes and roters for 1992 jeep wrangler
Yes. Almost everything from 1997-2005 is exactly the same.
1997 is the first year airbags were available for the Jeep Wrangler TJ. I know because I owned a 1997 and also recently had to sell my 7s CJ-5 to get another Jeep with airbags. Enjoy it
The front speakers in a 1997 Jeep TJ are 4"x6"
Underneath the battery.