Oldsmobile
Oldsmobile Intrigue
Nissan Maxima
Grand Am SE

Where is the PCV valve located on a 1998 Olds Intrigue?

636465

Top Answer
User Avatar
Wiki User
2005-09-14 11:58:14
2005-09-14 11:58:14

The PCV valve on a 1998 Oldsmobile Intrigue is located under the MAP sensor. If you remove the large plastic cover with 3800 written on it and look to the left side of the engine there is a sensor marked (Pressure Sensor) with 3 wires going into it. Unplug that sensor and turn it counter clockwise and lift it off and you will see the PCV valve under it. Here is a picture to go along with my answer. http://autorepair.about.com/library/illustrations/bl795lib.htm

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Change what?Change what?

User Avatar

The solenoid, as well as the related valve, are inside the transaxle valve body, which is inside the transaxle fluid pan. I'm not sure if it's the lower pan or the side pan.

User Avatar

On the 99 Olds Intrigue, the camshaft sensor is located on the rear of the engine. It is just above the starter.

User Avatar

What does 'service engine soon' light mean on a 1998 olds intrigue?

User Avatar

The camshaft sensor on the 99 Olds Intrigue is located on the engine block. It is under the starter, which has to be removed to locate the camshaft sensor.

User Avatar

After removing an EGR valve from the vehicle, the valve can be flushed with carburetor cleaner. If the valve still sticks then a replacement will be needed.

User Avatar

Most parts on the 1998 through 2002 Olds Intrigues are interchangeable.

User Avatar

In the right kick panel. On my 98 Intrigue it's it the engine compartment in the black box connected to the air filter.

User Avatar

Assuming it is in one of the two Intrigue fuseboxes, it will either be in the fusebox located under the hood and on the passenger fenderwell, OR it will be in the inside fusebox located on the right side of the dash where the dash meets the passenger door. CPC

User Avatar

Under the "sight shield," the plastic engine cover. Remove the two black 13mm nuts, then unhook from the clip on the rear valve cover. The PCV valve is located in the front valve cover, on the transmission end of the motor, opposite the oil filler cap. Check out this picture: 99intrigue.shutterfly.com/headgasket/97#103

User Avatar

I have a 98 olds intrigue and the blower motor resistor is located under the glove box behind the blower....

User Avatar

On the passenger side of the engine, toward the front of the side. Near the alternator.

User Avatar

where is the pvc valve located on a 1980 olds cutlass 3.8 v-6

User Avatar

Like most cars. The heater control valve is located inside the closed compartment with the heater core and the and the AC condenser. It is a door flap that seperates the heated air from the outside air, or the AC air.

User Avatar

wHereis the abs wheel speed sensor located on 1998 Oldsmobile bravadaI

User Avatar

Not knowing what engine you have in your Olds, most engines will have the "Mapping" of the belt located somewhere under the hood. On my two Olds, they are located on the valve cover. When you purchase a new belt for your car the cardboard holder for the belt will display several diagrams based upon the engine that the belt will fit..... you out.

User Avatar

Need to ask a complete question please. Yes, 98 olds should come with a driver's window.

User Avatar

The 1992 Oldsmobile IAC valve can be found attached to the firewall in the engine compartment. The valve will be on the passenger side of the firewall.

User Avatar

The firing order for an Olds Intrigue is 1-6-5-4-3-2. The number one cylinder is on the drivers side, closest to the firewall.

User Avatar

Should be able to access under hood at center firewall plastic panel may have to be removed


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.