Serpentine Belts
Chevy Suburban
Pontiac Sunbird

Where is the belt tensioner located on a 93 Pontiac Sunbird?

567

Top Answer
User Avatar
Wiki User
Answered
2010-09-16 01:35:27
2010-09-16 01:35:27

lokks to be on the lower right side of engine

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


I believe it to be on the fan belt mechanisim..the pulley that allows you to adjust the tension.

After you have released the tension from the belt, remove the 2 obvious bolts that hold it to the engine block.

if im not mistaken..it is behind the timing cover..it runs off the timing belt You are correct. It is the belt tensioner for your timing belt and a pain to release to release the tension and also not the easiest to replace.

On the main drive serpentine belt, there is a tensioner pulle. it is positioned at 6:00. relieve tension remove belt. reverse process for reinstallation.

Near the top of the belt there is a belt tensioner; it has a pulley attached to it. It is spring loaded and there is a provision to attach a breaker bar to force back the spring; once you do, it is easy to remove the serpentine belt.

the timing belt tensioner is located on the lower side of the rear head just below the camshaft drives

To remove the accessory drive belt or the serpentine belt from the motor on a 1989 Sunbird, it is necessary to loosen the belt tensioner. Look for a pulley that has a bolt in a slot. Loosen the bolt and move the tensioner so there is a gap in the belt. Then remove the belt from each pulley.

How do you change the supercharger belt tensioner in 1997 Pontiac Grand Prix GTP?

As viewing the motor from the front of the car, the belt tensioner is located on the left side of the engine. On what is essentially the front of the motor, the belt tensioner is located just below the idler pulley.

alternator on a 2000 Pontiac runs off a serpentine belt if its loose then chances are ur serpentine belt is worn or stretched or your tensioner pulley is bad or the tensioner itself..alternator bolts stable does not move like the old setup.

Front of engine (behind serpentine belt).

Remove the serpentine belt. Tensioner is below Alternator. Remove the three mounting bolts on the tensioner baracket assembly. Replace entire unit.

To change the serpentine belt on a 2003 Pontiac Bonneville, loosen the tensioner pulley and remove the old belt. The tensioner pulley is the wheel in the belt system that has a bolt through the middle in a slot that can be adjusted. Put the new belt on and tighten up the pulley.

The system that the belt runs on ,is called a serpentine system,it's a one belt set-up ,and they are self adjusted by a tensioner,sounds like...1- Your tensioner is seized,or ..2-your belt is streched..Sometimes the tensioner can be free'd by taking it of and working it in with lubrication,but if not,get a new tensioner and a belt, hope it helps.

Look at the belt on the engine, then look at the pulleys. The water pump is behind the pulley without any groves in the pulley.

anywhere on the belt most likely close to the alt.

Automatic belt tensioner - if not enough pressure replace tensioner Belt has streched too big, and the Automatic belt tensioner is at its limit. The tentioner is how yo remove the belt, so you should feel its tention with your wrench.

I'm guess you're asking about relieving the tension on the belt? The tensioner swivels away from the belt, thus loosening the belt. This is done by putting a wrench or socket or whatever you can fit, onto the front of the tensioner and rotating it.

Note:The drivebelt routing decal on the radiator shroud to help during drivebelt install * To replace the belt rotate the tensioner pulley clockwise to release belt tension * Remove the belt from the auxiliary components and slowly release the tensioner * Route the new belt over the various pulleys again rotating the tensioner to allow the belt to be installed then release the belt tensioner

The belt tensioner for a 94 Cavalier is mounted on the front of the engine. The tensioner is spring loaded on an arm to keep the belt tight.

You will need to loosen the tensioner pulley on your 1994 Pontiac Grand Am. The old serpentine belt will come loose and can be removed. Put the new serpentine belt on and tighten the tensioner pulley.

Note:The drivebelt routing decal on the radiator shroud to help during drivebelt install * To replace the belt rotate the tensioner pulley clockwise to release belt tension * Remove the belt from the auxiliary components and slowly release the tensioner * Route the new belt over the various pulleys again rotating the tensioner to allow the belt to be installed then release the belt tensioner

The belt tension should adjust automatically. There's a thing called a belt tensioner that has a strong spring in it (you can't see the spring) that keeps pressure applied to the belt. This belt tensioner is what makes the serpentine belt so hard to remove. Many times the tensioner is in a difficult place access.

Mine did this and I found out it was the timing belt that needed to be changed.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.