0
Where is the config file for the Botania mod to turn off the flow decay?
Wiki User
∙ 8y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What can speed up and slow down decay?
temperature; warmth speeds it up, cold slows it down. moisture; if it is moist it will decay quicker oxygen; if there is a good oxygen flow it should decay quicker. these all speed up decay because the bacteria and fungi that cause decay need these conditions to thrive and multiply
How does xerostomia affect dental decay?
Xerostomia is the medical term for 'dry mouth' or inadequate salivary flow. Adequate salivary flow is important because saliva helps wash away food debris after eating. Saliva also contains buffering agents that tend to neutralize the acids produced by oral bacteria. These acids are responsible for tooth decay. Therefore a lack of salivary flow, xerostomia, will result in increased risk of tooth decay.
What does the mantle remain from radioactive decay?
Very hot and although still solid able to flow in convection currents.
How does convection current occur in the mantle?
radioactive decay takes place, which produces lot of heat and causes the mantle to flow in convection currents veena
Which file contains all permanent information and is updated during processing by transactions of data?
To help here we need to see the file structure you have and the data flow
What has heat flow got to do with radioactivity?
The primal heat from the deep interior of the Earth is mainly due to radioactive decay, with a small contribution due to gravity compression.
Why do nutrients need to be broken down before they can be used?
The soil can not deal with a huge amount of matter so to make it easier it breaks it down then the nutrients from they decay flow into the soil.
Is it possible to write a C plus plus or java program to draw an activity flow diagram given the sequence as a text file input and store the diagram in an output file?
Yes, this is possible.
What is the process of transferring data in a continuous and even flow allowing users to access and use a file while it is transferring?
streaming
What are tectonic plates referring to?
The plates of crustal rock floating on the mantle rockand being moved by the flow of mantle rock in convection cells driven by the heating of radioactive decay deep in the core and lower mantle.
What is meaning of input process output?
AnswerInput Process Output is what you put in, what you use both input and output for, and also what you get out. For example you might put in your monthly expenditure and income (input) , then you can work out your average (process) and then finally create a graph (output).Hope this helps!! lolDocumentationIn the front of a program's documentation there should be a page with a rectangle in the middle. It is called the 'process' symbol on flow-charting templates. That represents the computer doing the processing. It should have the ID of the program in a band at the top and the name of the program in the body.Above, fanned out, there should be a vertical set of file 'icons' as per your flow-charting template. Files usually have an ID. Draw a line just below the top of each file icon and write the ID in there.Inside each file icon you put the name of a file from which the program receives input.To the side of the rectangle fanned out there should be a vertical set of file 'icons' . Inside each file icon you put the name of a file which the program updates.Below fanned out there should be a horizontal line of file 'icons' as per your flow-charting template. Inside each file icon you put the name of the file which the program creates containing output only.This document gives a maintenance programmer a useful overall picture.
How do you configure CISCO pix 515 firewall?
To configure a Cisco PIX 515 Firewall, first, connect your Cable or DSL modem to the Ethernet 0 interface on the firewall with a Straight-Through Ethernet RJ45 cable. Then, connect another Straight-Through Ethernet RJ45 cable from the Ethernet 1 interface on the firewall, to an available port on a switch or hub. Then, connect the blue rollover cable from the Console port on the Cisco PIX 515, to the serial port on your computer. Then, turn the firewall on. Then, open HyperTerminal. Once you open HyperTerminal, type in any name that you want to use. Then, select any icon. Then, click OK. Then, next to "Connect Using," select the proper serial port, that you connected the rollover cable to. Then, click OK. Next to "Bits per second," select 9600. The "Data bits" should be 8, the "Parity" should be none, and the "Stop bits" should be 1. Next to "Flow control," select none. Then, click OK. Then, press Enter on your keyboard. If it asks you to perform an initial configuration, type no. Now, you should be at the firewall's prompt, which should look similar to pixfirewall>. The commands below are using pixfirewall as the prompt. Now, follow the commands below: pixfirewall> enable (If applicable, type in a password. If no password was assigned to the firewall, just continue). pixfirewall# configure terminal pixfirewall(config)# nameif ethernet0 outside security0 pixfirewall(config)# nameif ethernet1 inside security100 pixfirewall(config)# name x.x.x.x pix_outside (Note - The x.x.x.x represents your "outside" IP Address, or the IP Address that your ISP is giving you). pixfirewall(config)# name x.x.x.x PIX_inside (Note - The x.x.x.x represent the IP Address for the local network interface on the firewall (the Ethernet 1 interface). pixfirewall(config)# interface ethernet0 100full pixfirewall(config)# interface ethernet1 100full pixfirewall(config)# ip address outside pix_outside 255.255.255.0 (Note - The 255.255.255.0 here assumes that it is the subnet mask for your Internet connection. If your Internet connection uses a differnet subnet mask, replace that subnet mask with the correct subnet mask). pixfirewall(config)# ip address inside pix_inside 255.255.255.0 (Note - The 255.255.255.0 here assumes that your local network (inside network) uses that subnet mask. If you are using a different subnet mask for your local network, replace that subnet mask with the correct subnet mask). pixfirewall(config)# ip address inside x.x.x.x (Note - The x.x.x.x represents the IP Address for the local network interface on the firewall (the Ethernet 1 interface). pixfirewall(config)# outbound 10 deny 0.0.0.0 0.0.0.0 0 ip (Note - The 2 outbound commands below only allow ports 80 and 443 to go outbound. If you do not want to block any ports that go outbound, do not type the following 2 commands in). pixfirewall(config)# outbound 11 permit 0.0.0.0 0.0.0.0 80 tcp pixfirewall(config)# outbound 12 permit 0.0.0.0 0.0.0.0 443 tcp (Note - The command below is used if you do not want to block any outbound ports). pixfirewall(config)# outbound 10 permit 0.0.0.0 0.0.0.0 0 ip pixfirewall(config)# NAT (inside) 1 0 0 pixfirewall(config)# Global (outside) 1 interface pixfirewall(config)# route outside 0 0 <gateway IP address> 1 (Note - The Gateway IP Address is the Default Gateway for your Internet connection, that your ISP is giving you). pixfirewall(config)# write memory This completes the configuration of the Cisco PIX 515 Firewall.
