0
What else can I help you with?
Where is the lambda sensor on a 2 liter Mk III mondeo tdci?
On a 2-liter Mk III Mondeo TDCi, the lambda sensor, also known as the oxygen sensor, is typically located in the exhaust system. There are usually two sensors: one positioned before the catalytic converter (upstream) and another after it (downstream). To access the upstream sensor, you may need to raise the vehicle for better visibility and reach. Always consult the vehicle's repair manual for specific details and guidance.
How do you activate the alarm on a Ford Mondeo mk 3?
Smash the driver's side window in with a hammer then try to hotwire it. Should activate the alarm nicely.
Where is diagnostic port mk 2 mondeo?
The diagnostic port on a Mk 2 Ford Mondeo is typically located under the dashboard, near the driver's side. You'll usually find it just above the pedals, towards the center console. It may be covered by a plastic panel, so you might need to remove that for access.
What MK is 2002 Ford Mondeo?
The 2002 Ford Mondeo belongs to the Mk3 generation, which was produced from 2000 to 2007. This model featured a more refined design and improved technology compared to its predecessor, focusing on comfort and handling. It was available in various body styles, including sedan, hatchback, and station wagon, and offered a range of petrol and diesel engines. The Mk3 Mondeo was well-received for its practicality and performance.
A wiring loom to fit rear electric windows in your mk 1 mondeo does this need to come from another mk 1 or can you use a mk 2 loom?
I would only use the wiring loom from a MK1, as the MK2 wiring could be completely different!
Are the wiper and reversing lights connected on a Mondeo tdci Mk 3?
Yes, on the Ford Mondeo TDCi Mk 3, the wiper and reversing lights are connected through the vehicle's electrical system. This means that certain electrical faults or issues can potentially cause both systems to malfunction simultaneously. If you're experiencing problems with either, it's advisable to check the wiring and connections for any shorts or faults. Always consult a professional or refer to the vehicle's service manual for troubleshooting guidance.
If you have a Ford Fiesta which is registered in November 1999 how do you tell if it is a Mark 4 or a Mark 5 as there is nothing in the paperwork?
you can tell by the front headlights if they are a long flat lights its a mk 4 and if not the its a mk5
What year did Ford roll out the Cortina MK3?
The Ford Cortina MK 3 was initially placed in the automobile market in 1970. Production of the MK 3 ceased in 1976. Ford's Cortina line was designed for sale in the UK and neighboring European countries.
Where is Vauxhall Astra Speed Sensor?
I am fairly sure that the Astra G (Mk 4) models withoutABS have the speed sensor in the gearbox, and the ABS models take the road speed from the left-hand front wheel hub. Unfortunately, the gearboxes fitted to ABS models have the speed sensor hole plugged, so this is something to consider if replacing the gearbox.
Ferrari held a winning streak at Le mans race till what year?
1966, when Ford won with the Ford GT Mk 2.
Where is the outside air temperature sensor on a VW Golf Mk 5?
Stand in Front of the car. On the front bumper there are three air vents. Small one on left, same size on right hand side. The middle one is slightly larger. Look through the middle one. You will be able to see the sensor with its wires attached to it. You can't miss it. To get to the sensor you will have to remove the vent. Remove the vent starting at the corner on top. Be careful as the clips breaks easily. Good luck.
How do you change the bonnet lock on a mondeo mk 3?
To change the bonnet lock on a Mondeo MK3, first, ensure the bonnet is open and secure. Disconnect the battery to prevent any electrical issues, then remove any necessary components obstructing access to the lock, such as the grille or front panel. Unscrew the old lock mechanism from its mounting points, disconnect any cables, and then install the new lock in reverse order, ensuring everything is securely fastened. Finally, reconnect the battery and test the lock to ensure it functions properly.
