answersLogoWhite
Fuel Pumps
Chevy Silverado
Jeep Comanche
Ford Expedition

Where is the fuel pump inertia switch located on a 1991 Jeep Comanche?

121314

Top Answer
User Avatar
Wiki User
Answered
2011-09-13 10:46:34
2011-09-13 10:46:34

there isn't one...

001
🦃
0
🤨
0
😮
0
😂
0

Related Questions


Plymouth does not use inertia/reset switches


Doesnt have one....inertia switches are used one Ford vehicles


According to the wiring diagram, there is no inertia switch. There is only a relay switch in a 1991 Isuzu Trooper.


General Motors products do not use inertia/reset switches.


If its the same as the 1991 Ford EXPLORER , check in the front passenger footwell , under the front edge of the carpet , on the toe board , just to the right of the transmission hump for the fuel pump inertia switch



GM vehicles do not use inertia/reset switches.


Check in the front passenger footwell , under the front edge of the carpet , just to the right of the transmission hump . I believe that is where the fuel pump inertia switch ( shut off switch ) is located in a 1991 Ford Explorer


GM vehicles are not equipped with an fuel pump inertia switch.


No it does not. Chevy did not use them in that year on there trucks.


I'm not a mechanic / technician but check in the front passenger footwell , under the front edge of the carpet , mounted on the toe board just to the right of the transmission hump . I believe that is where the inertia switch was on my 1993 Ford Explorer


In the right front passenger footwell , under the front edge of the carpet , mounted on the toe board to the right of the transmission hump


Dodge does not use inertia/reset switches.


It does not have one. Chevy did not use them on there trucks.


On my 1991 fuel injected Festiva the fuel pump inertia switch is located inside the panel at the rear driver's side. Lift the rear hatch and look to the left where the seat belt attaches and the speaker is located. There is supposed to be a small panel (2 or 3 inches square). My panel is missing and there is just an opening. You can see the top of the inertia switch with a red button. If you need to replace it or get to the entire switch you must remove that entire panel. It only takes about 10 minutes to remove that panel.


No it is not, You will have to remove the fuel pump relay are fuse. Only ford had a INERTIA switch.



If I remember correctly , on my 1991 LX 5.0 L it was in the rear of the trunk under a removable rubber " plug " , your 1993 should be the same


Funny looking thing behind the carpet under the glovebox


I'm not a mechanic / technician but check in the trunk / hatch area between the taillights . See if there is an oval shaped rubber plug . The fuel pump shut off switch ( inertia switch ) was located there on my 1991 Ford Mustang behind the rubber plug


Bad fuse or fuel pump inertia switch " tripped " or bad wiring connection


try going to www.autozone.com and enter your vehicle info and look for the inertia switch location.


The turn signal switch location on a 1991 Chevy Lumina is behind the steering column. You will need to use a socket set to get to the switch.


Check inside the center console, under the front seats, behind the glove compartment or behind the driver or passenger-side kick panels. This is where you can find the fuel pump inertia switch on a 1991 Nissan Sentra.


The fuel pump inertia switch location on 1991 to 1994 Ford Explorers is in the right front passenger area , under the front edge of the carpet , on the toe board , to the right of the transmission hump



Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.