0
Where is the neutral bus bar in a stab-lok panel BE116-32 125 amp.?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can you hook up 200 amp dervice to a 125 amp service panel?
No. If device draws 200 amps breaker will trip.
Should a 2 AWG copper wire be used to feed a 125 amp sub panel located 125 feet from main panel?
No, the conductor is too small. The feeder to a 120/240 volt sub panel should be a 1/0 copper or a 2/0 aluminium conductor. This size conductor will limit the voltage drop to 3% or less when supplying 125 amps for 125 feet on a 240 volt system. ACWU 90 (Armoured Cable Wet location Underground 90 degree C). ACWU 90 cable is code approved for direct burial and is used in many projects as an underground service distribution feeder. Aluminium is much cheaper than copper for this type of installation.
How can you find out the bus bar rating in a panel that is old and the rating sticker has fallen off is it safe to say that a panel with a 100 amp main breaker has a bus rated AT 125 AMPS?
A 100 amp panel should have a conservatively rated busbar and wiring but this says nothing about your particular panel. If you are asking a question relating to safety it needs to be seen by an electrician.
What size wire is needed to feed a 125 amp sub panel from a 200 amp panel less than 200 wire feet away?
A #1 copper wire with an insulation rating of 90 degrees C is rated at 140 amps.
How many 50 amp breakers feeding 50 amp outlets can you install from a 125 amp main panel?
Three or four would be normal. The total current should not exceed the rating of the main panel, so depending on how intensively the different circuits are used, more could be installed.
How many amps can be put on a 125 amp service?
You should not load a 125 amp panel any more than 100 amps.
What is the shift pattern a suzuki rm 125?
Shift pattern from neutral is 1 down, 5 up.
How many electrons does a neutral atomof hugeonium have?
The as yet undiscovered and fictional element hugeonium will have many electrons, possibly in excess of 125.
What size aluminum wire to feed 125 Amps 220 volt a distance of 175' and what size ground?
A 3/0 aluminum conductor will limit the voltage drop to3% or less when supplying 125 amps for 175 feet on a 220 volt system. If the 125 amp load is a sub distribution panel that is not going to be fully loaded to 125 amps then using the exact connected load, which might be smaller than 125 amps will effect the wire sizing. The grounding conductor for that size distribution panel is #6 bare copper.
Can you swap out your 125 amp panel for a 200 amp panel?
You can but you may need new Service wires ran to your house to support the larger load. You will probably be looking at paying a couple thousand dollars for it.
How much weight can this mount hold?
This mount can hold up to 125 pounds, and accommodates most 52" flat panel TVs.
Can you hook up 200 amp dervice to a 125 amp service panel?
No. If device draws 200 amps breaker will trip.
How do you change gears on a kx 125?
Down is 1st, up is 2nd to 5th and between 1st and 2nd is neutral. (I hope you didn't mean clutch plates).
What size cable for 125 amp sub panel?
A #2 copper conductor with an insulation factor of 90 degrees C is rated at 130 amps.
Should a 2 AWG copper wire be used to feed a 125 amp sub panel located 125 feet from main panel?
No, the conductor is too small. The feeder to a 120/240 volt sub panel should be a 1/0 copper or a 2/0 aluminium conductor. This size conductor will limit the voltage drop to 3% or less when supplying 125 amps for 125 feet on a 240 volt system. ACWU 90 (Armoured Cable Wet location Underground 90 degree C). ACWU 90 cable is code approved for direct burial and is used in many projects as an underground service distribution feeder. Aluminium is much cheaper than copper for this type of installation.
How can you find out the bus bar rating in a panel that is old and the rating sticker has fallen off is it safe to say that a panel with a 100 amp main breaker has a bus rated AT 125 AMPS?
A 100 amp panel should have a conservatively rated busbar and wiring but this says nothing about your particular panel. If you are asking a question relating to safety it needs to be seen by an electrician.
Your rm 125 is slipping out of 2nd gear to either neutral 1st or 3rd oil changed and still the problem continues help?
Its either the dogs or the shift forks
