If the problem was fixed, the check engine light should turn off after a certain amount of times of turning on and off the car.
There is no reset button for the check engine light. It must be reset with an OBD scan tool.
The light is reset with a scan tool after the repair. There is not a button.
There is no reset button for the check engine light. You can have Mitz. do it for $$$ or you can remove the negative battery line for a few seconds and replace. That will reset the check engin light.
The check engine light on a BMW 525i is reset by pressing the trip reset button until the engine icon appears. The Check and DC buttons are used to navigate between menus and the trip button held to actual reset the selected error.
Sorry , there isn't a reset button - you have to have the Explorer scanned to find the trouble code(s) that caused the check engine light to come on . The problem has to be repaired before the check engine light can be turned off by using the OBD II scan tool
It is very easy to reset the check engine light on a VW car. All you have to do is to push the wrench button located near the trip reset. You will hold it in while turning on the ignition. after the service message appears, let go of the wrench button and hold in the minute button. Turn the ignition off and the computer will reset.
You can usually disconnect the battery cable for about 15 seconds and reconnect it to reset the engine light. Check the fuse box for a(red) resert button - to reset the engine light disconnect battery for 15 minutes , the red reset button on fuse panel is for motor oil change reminder reset
Press the odometer button while starting the vehicle. Keep holding down the button until the numbers disappear and the check engine light goes out. Release the button and all is well.
The check engine light is reset with a scan tool after repairing the cause of the fault.The check engine light is reset with a scan tool after repairing the cause of the fault.
You reset the check engine light with a scan tool after repairing the failure.
The check engine light has to be reset with a OBD scan tool
Reset button for what? If you are talking about the check engine light, there is no reset button. Unhook the battery for 5 minutes and see if that resets it. If not, then it can be reset with a scanner. Of course it will come right back on if the problem is not corrected.
Press and hold the odometer reset button while turing the ignition switch on without starting the engine. After 5 seconds the light will go out.
how do i reset the check engine light on a 1999 acura 3.2tl
on most vehicles if you disconnect the battery cables it will reset the check engine light
hoe do you reset the check engine light in a 1995 land rover
Is there a reset button on a 1996 rav4? Had it checked out, and said it need spark plugs and wires. Replaced it and check engine light still on.
I asked this forum for the answer and found it myself. I actually resorted to reading the owners manual. Here's the answer... -Make sure the engine is off. -Press and hold the RESET button on the Trip Odometer. -While holding this reset button turn the key until the dashboard lights come on (the Accessories position). -Keep holding the Reset button for an additional 10 seconds. -After 10 seconds the check engine light should go out. It is now reset. I tried this today and it worked. The light hasn't come back on yet. There are various reasons for the light coming on. In my case I needed an oil change and the mechanic forgot to reset the light when he was done. If you truly have a problem, it will come back on. That is wrong, that is how you reset the maintenance required light. Check engine light is a different light.
The check engine light comes on in a car when there is a problem with the engine. It will go off or be reset when the problem is fixed.
That is not how you reset the check engine light. That trick can only be used to reset the airbag light (something I have had to do often). Reseting the CEL involves doing specific maneuvers with the screw on the ECU. Check out SR20forum.com
You need a scan tool to properly reset the check engine light.
How do you reset check engine light for the 2009 Chevy trail blazer?
No there is not a reset button. You can try disconnecting the negative battery cable for 5 minutes and that may reset the check engine light. If not it will have to be reset with an OBD2 scanner. Remember if you do not repair the problem that caused the light to come on you are wasting your time resetting it as it will just come back on.