answersLogoWhite

0

at l/3

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

Where are Joint locations in multi-layer wood beam?

Guidelines are; 1. Staggered 2. Uniform


What is plank and beam construction?

Plank and beam is typically referred to as post and beam. This type of construction is used a large percentage of the time for new home construction. It is used in colder climates more than warmer climates because you have the ability to insulate under the floor of the house. In warmer climates slab floor construction is used more than it would be used in colder climates. There is another type of construction that is used but not as often. It is called the joist system. This is the way Post and Beam construction works. A vertical member (post) is set on concrete pads, about 8 feet apart. The horizontal member(beam) is set on the posts. The spacing between the beams are typically 4 feet apart. The end of the beams are placed in beam pockets that have been designed into the foundation. Then 2"x6" or 2"x8" tongue and grove planks are placed perpendicular on the beams to create the floor. In slab construction you pour a concrete floor between the footing and foundation. A joist system uses 2x material to span between two points and tie into a ledger board using metal hangers. This system is used for decks more often and the 2nd and 3rd floors of homes.


What is an i-beam?

I-beams are divided into ordinary I-beams, light I-beams and H-beams. I-beams are mainly used in crossbeam construction. Shanghai Changzheng produces I-beam, if you are interested in I-beam, welcome to consult with our company.


What is the purpose of camber in steel beam?

Camber is the amount of deflection provided in the opposite direction of loadings. That is when the beam is subjected to Vertical downward loadings, the beam has a tendency of deflecting downwards. In this case, camber value is to be given in the upward direction so that when it is fully loaded condition, the beam would have almost zero deflection. Similarly, when the beam is subjected to vertical upward loadings, the camber value is to be given in downward direction. The purpose of camber in steel beam is to have almost zero deflection w.r.t.o beam axis after loading of beam as highlighted earlier. by R.Ravichandran, Chennai-49


What is t beam?

It is a monolythic concrete beam consisting of a web and a flange to form the shape of a"T" .

Related Questions

Why should you provide a plinth beam?

Plinth beam is provided to 1. support the wall above it 2. act as tie beam for columns


What is meant by Beam column joint?

beam


Why upstand beam is provide?

The upstand beam is very important as it provides support to the given structure. The upstand beam should remain fixed until the construction is over.


What is the definition of a drag beam in construction?

A drag beam in construction refers to a short beam used to secure a hip rafter's foot to neutralize its thrust. It is also known as a "dragon beam" and "dragging beam," among several other monikers.


Where can you get info on post beam construction?

Vermont Timber Works has an extensive web site on timber frames and post & beam construction.


What is the recommended type of steel beam for deck construction?

The recommended type of steel beam for deck construction is typically a wide-flange beam, also known as an I-beam. These beams provide strong support and stability for the deck structure.


Why is up stand beam provided?

beam is provided to support the externally applied forces i.e deadload,liveload,windload.


What is the Tagalog construction term of beam?

biga


What types of construction lights are available?

The types of construction lights that are available are high voltage beam light and a low voltage beam light. The high voltage beam light shines a lot brighter.


What mean by anchor bar in beam reinforcement?

the top reinforcement of beam (compression face of beam). it is provided to hold the stirrups in place.


Is it possible to strengthen beam column joint with ferrocement laminates?

yes


How do you provide expansion joint in slab beam construction 75 meters in length?

The purpose of expansion joint , is to anticipate movement of structure due to temperature, earthquake,settlement. In 75 mtrs length of slabs we can make expansion joint in L/2 or 75/ 2 or L/ 3 for every 25 mtrs , we provide bearing Pads for movement. , actually this also name as movement joint.