Want this question answered?
These terms apply to the coils inside a wattmeter. 'Pressure coil' is an archaic term for 'voltage coil', which is connected in parallel with the supply, while the 'current coil' is connected in series with the load.
No. In order to induce an EMF, the coil and the magnet must be moving in relation to each other.
The potential difference across the secondary coil will be 147.42 Volts
Speed of movement of coil and the number of turns in the coil
A 'pressure coil' is an archaic term for a 'voltage coil' (UK terminology) or 'potential coil' (US terminology), as opposed to the 'current coil' in a wattmeter. This coil is connected in parallel with the supply, while the current coil is connected in series with the load.
These terms apply to the coils inside a wattmeter. 'Pressure coil' is an archaic term for 'voltage coil', which is connected in parallel with the supply, while the 'current coil' is connected in series with the load.
No. In order to induce an EMF, the coil and the magnet must be moving in relation to each other.
The potential difference across the secondary coil will be 147.42 Volts
burn or burst
No, there is not any difference between the switching action of a relay and a contactor. Both of these devices are operated by an electro magnetic coil.
Speed of movement of coil and the number of turns in the coil
It's an archaic expression, which is not usually used these days. But 'voltage' was considered to equate to 'pressure' in, say, a hydraulic system. So the term pressure (as well as 'tension') has, in the past, been used in place of 'voltage' or 'potential difference', as in 'pressure coil' or 'high-tension transmission'. In North America, a 'voltage coil' is frequently termed a 'potential coil'.
Motion of a coil within a magnetic field will induce a current in the coil if it can complete a circuit.
The primary coil has to induce current in the secondary coil. The only way this can happen is if there is a varying magantic field in the primary which then will induce a varying mag field in the secondary which results in a current in the sec. Only varying current can induce a varying mag field only a varying mag field can induce current So you need a varying current in the primary. D.C. is not a varying current so it cannot induce a mag field in the coil. A.C. (it does not have to be +/- it just has to be varying) can do so.
Voltmeters and Potentiometers are used to measure potential difference.2nd Answer:Not true. While a voltmeter is indeed used to measure potential difference, the potentiometer is a rotating control device, like a volume control on a radio. The potentiometer is actually a variable resistor, and measures absolutely nothing.
There is no such thing as an 'induced current'. Voltages are induced, not currents. If a voltage is self-induced into a coil, then that voltage will oppose any change in current. If a voltage is mutually-induced into a separate coil, no current will flow unless that coil is connected to a load.
Different ways to induce current in a coil are as given below:(1) If a magnetic field is changed round a coil then an induced current is set up in the coil. It can be done by taking a bar magnet and bringing it closer to the coil or taking it away from the coil.(2) If a coil is moved in a magnetic field, then again an induced current is set up in the coil.(3) If a coil is rotated in a uniform magnetic field, it may also cause an induced current in the coil.(4) If we take two coils and insert them over a non conducting cylindrical roll then on changing current flowing in one coil, an induced current is obtained in the other coil.CommentYou don't induce a 'current' into a coil; you induce a voltage. If that coil is open circuited, then no current will flow. If, on the other hand, the coil is connected to a load, or its opposite ends short-circuited, then the induced voltage will cause a current to flow. Remember, current will only flow if there is a load, or short circuit, and the value of the current will depend upon the value of the induced voltage and the resistance of the load or short circuit.