0
Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute?
Wiki User
∙ 13y ago
Ctrl-Shift-6
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute process?
ctrl-c Actually, I believe ctrl-c will only work from a Dos command line prompt. I believe the correct answer is Ctrl-Shift-6 for CLI
Which networking command is most popularly used to test the connectivity of between systems and networks?
The ping command. Traceroute is also useful, but I would start by using the ping command.The ping command. Traceroute is also useful, but I would start by using the ping command.The ping command. Traceroute is also useful, but I would start by using the ping command.The ping command. Traceroute is also useful, but I would start by using the ping command.
What would be the basic word for interfere?
to interrupt
At Which Prompt would you configure the Hostname on a Cisco Router?
You can do this on the enable, or privileged, prompt.
What is a sentence using the word interrupt?
Sorry to interrupt, but the files are ready to be photocopied. I wish you would not interrupt me while I am deep in meditation. How dare you interrupt my sentence again, you imbecile! This is the last time you will interrupt our dinner, Jenny, before I come over there and smash that phone through your face. If you interrupt the teacher while she is speaking, you will get a warning. Don't interrupt me today, I have far too much work to be getting on with.
What utilities would you typically use to determine the number of hops to a specific destination?
You use the traceroute utility. In Windows, go to the command window, and type tracert, followed by an IP address or a domain name.You use the traceroute utility. In Windows, go to the command window, and type tracert, followed by an IP address or a domain name.You use the traceroute utility. In Windows, go to the command window, and type tracert, followed by an IP address or a domain name.You use the traceroute utility. In Windows, go to the command window, and type tracert, followed by an IP address or a domain name.
Why there is a need for disabling interrupts in 8085?
Interrupt are automatically disabled on interrupt entry (except for TRAP, which is non-maskable) so that interrupts do not, by default, nest. You would also disable enterrupts surrounding a critical section of code that, perhaps, manipulated an interrupt register. It is possible to re-enable interrupts during an interrupt service routine. Typically, you would have a hierarchy, such as RST7.5, then RST 6.5, then RST 5.5. Initially, at interrupt entry, all interrupts are disabled. You could then manipulate the interrupt mask using the RIM and SIM instructions and enable further interrupts, allowing a nested architecture. At interrupt exit, then, you would disable interrupts, reset the mask, enable interrupts, and return from interrupt.
What are interrupts initiated by instructions called?
Those would be software interrupts. Interrupts initiated by the hardware would be hardware interrupts. While the socket a mouse is plugged into would use a hardware interrupt, a mouse driver would use a software interrupt.
What command would you type at a command prompt?
#(8======>)
What is software interrupt with examples?
Interrupt generated by executing an instruction is called software interrupt. It's also called 'trap'. Software interrupts are generally used to make system calls i.e. to request operating system to perform an I/O operation or to run a new program.Examples:C++:A cout or cin statement would generate a software interrupt because it would make a system call to print something.A fork() statement in Linux would generate a software interrupt because it would make a system call to create a new process.Assembly IA32:The instruction int 21h would generate a software interrupt which would request something from operating system (depending on the register values).
How can you identify by seeing in the prompt whether the command is external or internal in unix?
You really can't. There is nothing in a prompt that would give that information.
How would you prompt somebody?
you would stick your finger up their fanny and tickle
