0
Why do you install RAM and CPU before installing the motherboard into the case?
Wiki User
∙ 11y ago
You don't have to do this, but it is generally easier to manipulate the motherboard and components before you put it inside the case, which due to limited space can make it rather awkward.
On the other side, if a motherboard is installed prior to components, it will have a lot more support from its holding brackets etc. This can be very important for installations that may put pressure/bend the motherboard body. A good example of this, as pointed out by ID1198720506 are components which use latch/snap mechanisms to lock on to the motherboard.
Wiki User
∙ 11y ago
Wiki User
∙ 15y agoI would recommend installing the Processor (+ heat sink and fan) and the memory.
Add your answer:
Earn +20 pts
Why is it best to install drives into a computer case before you install the motherboard?
Because you might drop the drives on your motherboard while installing.
Technician is assembling a new computer Which two components are often easier to install before mounting the motherboard in the case?
Before mounting the motherboard in the case I like to install the CPU and CPU fan/heatsink on to the motherboard. In fact, it is recommended to install the CPU & heatsink while the motherboard is still our of the case to make the job easier.
What is the purpose of installing standoffs or spacers between the motherboard and case?
To Prevent components on the back of the motherboard from touching the case.
When assembling a systemwhat order do you put components into the case?
You can assemble them in any order you like - whichever is most convenient for you. People usually install the chips into the motherboard before installing it into the case, followed by video card, modem car etc, and power supply.
Why is it best to install drives into a computer case before you isntall the motherboard?
Perhaps, because there might be not enough place after you install the motherboard to install your drives. The CPU or the RAMs might be in they way. There is surely no other magical reason to it.
What type of motherboard and case will you need to install a riser card?
nlx
How do you install a mother board?
Making sure that the computer case you have is appropriate for the motherboard is the first step. Then it is much like legos. The motherboard will only fit in the computer case in one way. So will the Processor, the harddrive, the ram, the processor fan, and all the other parts. Do not force anything into place, if it does not go in easily try reorienting it. (The motherboard usually has screws and mounts, line them up with the case, and do not fret)
When using Windows you should create a restore point before installing new software?
Creating restore points can often be helpful before installing and removing programs in case something happens and the program fails to install correctly or is removed incorrectly.
What should you do before disconnecting the wires leading from the front of the computer case to the motherboard if you don't have the motherboard manual handy?
d
How do you install a motherboard in a computer case?
You must first see if the screw holes on the board line up with the holes on your computer case. If they don't then you cannot use that motherboard and case together. Assuming this is an ATX case, you must first install the IO shield into the large square rectangular hole in the back, assuming the correct one isn't already installed. You will need the one that comes with the motherboard, not any that may come with the case unless they are identical to the port arrangement on your motherboard.You will need a power supply if the cased doesn't already have one that is compatible with your motherboard.Next, you will need to install a set of stand offs. These screw into the case and then screws are used to fasten the motherboard to these. This keeps the motherboard from touching any part of your case, since this can damage your motherboard when the power is on. The standoffs should look something like this. If your computer case did not come with any, or you don't have enough, you can buy them at this link. You can also use nylon stand-offs, depending on the type of case. If there are wedge-shaped slots in places rather than screw holes, then you'd need the nylon standoffs that snap into the motherboard holes and slide into the groove. Then you'd use the other kind of standoffs with screw holes in the case. There are also nylon standoffs that screw into the case and the motherboard snaps over.After you screw in the standoffs, then you may want to wire or partially wire your case at this point. You will have to refer to the wiring diagrams in the manual, and you may need to find help doing this if you cannot make sense of the diagrams. The audio jacks and the USB headers are often the hardest to wire. In some situations, the motherboard's audio wiring and the case's audio wiring don't match. So you may have to guess at the audio wiring, or better yet, omit wiring it. This problem occurs when using a modern Intel motherboard in an older AMD-compatible case. So you should figure out how to reconcile this before installing the motherboard. You'd also install your RAM and CPU at this time.So after you've wired the motherboard, or if you plan on doing it last (harder), then you screw in your motherboard. Make sure you have secured but not over-tightened the screws and that the motherboard is not directly touching any part of your case.Then you install a video card unless the motherboard has one. At this point, if the front panel and power supply are wired, the memory and CPU are in their sockets, the heat sink and fan (or other cooler) are installed, the board is properly mounted using standoffs, and you have a monitor attached to a video card that is installed, then you can attempt to power it up. If it POSTs properly or gives you error messages, then you were likely successful. But also check to see if the front panel lights are working since you might have reversed the wires.
How hard is it to put a motherboard in a case?
Motherboards are very easy to install, all you need are standoffs and a standard phillips screwdriver.
Your computer will shut down when you turn on it?
Bad PSU, (power supply). Did not install motherboard right in case, and bad ground.
