0
I would have to say the 0 guage. It's heavier and if your strong enough you could swing it at someone pretty hard. It would have to hit the person harder than the 4 guage.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What gauge of wire is needed to carry 200 amps?
3/0 gauge
What wire gauge size is the thickest 14 8 0 -33?
As far as I know there is no -33 gage wire. If you meant + then that would be the thinnest so 0 is the answer
What gauge wire to use for 70 amp service going 200' underground?
I would recommend you use 1/0 gauge
What wire gauge is needed to carry 150 amps at 240 volts?
At the service entrance you will need AWG 1/0 gauge.
What size USE wire is needed for 200 amps?
As a service entrance wire you need AWG # 3/0 gauge copper.
What gauge of wire is needed to carry 200 amps?
3/0 gauge
What size gauge wire for 4000w amp?
on a 4000 watt amp the best gauge wire woul be between 2 and 0
What does GA for tubing stand for?
the answer is gauge its a measurement of thickness in wire the 4 gauge (ga) wire ran from my car battery to power my audio amp. the smaller the number the bigger the wire usually from 24 gauge to 1/0 gauge which is about a inch thick
What wire gauge size is the thickest 14 8 0 -33?
As far as I know there is no -33 gage wire. If you meant + then that would be the thinnest so 0 is the answer
What gauge wire to use for 70 amp service going 200' underground?
I would recommend you use 1/0 gauge
What wire gauge is needed to carry 150 amps at 240 volts?
At the service entrance you will need AWG 1/0 gauge.
What size USE wire is needed for 200 amps?
As a service entrance wire you need AWG # 3/0 gauge copper.
What gauge wire for service entrance in Wisconsin?
Depends on the size of the service. 100 amp service will require 3 gauge, 150 amp service will require 1/0 gauge, and 200 amp service will require 3/0 gauge.
What is the max amps for 0 gauge wire?
A 1/0 copper wire with an insulation factor of 75 or 90 degrees C is rated at 150 and 155 amps respectively.
What size of wire needed for 220volt?
Wire is not sized by voltage. It is sized by current measured in amps. Some common copper wire sizes and their current capacities are: 15 amps -- 14 gauge wire 20 amps -- 12 gauge wire 30 amps -- 10 gauge wire 40 amps -- 8 gauge wire
What wire gage for 130' supply 100 amp service?
I would run 1/0 gauge.
Is there such a thing as Gauge 0 wire?
It is quite possible that this question "Gauge 0 wire?" was actually meant to be an Answer rather than an Alternate-Wording-To the original question, from which "Gauge 0 wire?" was split away: "What wire gauge is used for an electric range?".If that is so, then a comment to the suggestion that Gauge 0 wire might be suitable, is that insulated Guage 0 wire is very thick indeed and would not often have to be used in wiring for normal domestic use in homes. Even for high-powered appliances, such as 240 Volt kitchen ranges or clothing dryers, Guage 6 wire would usually be thick enough to be used safely for the kinds of lengths of runs needed in normal size houses.What exactly is being asked by this question "Gauge 0 wire"?Is it about some mechanical work? (Making a cage for an animal?)Or what diameter Gauge 0 wire is?Or of what kind of material Gauge 0 wire usually comes in?Or is it asking if Gauge 0 wire is the right size to use in some electrical work?(Like how many Amps can it carry safely without overheating?)One factor to decide the wire guage is the length of the run from the main circuit breaker panel to the appliance because, the thicker a wire is, so the lower its electrical resistance is. That is why, to prevent the wire from becoming hot enough to start a house fire, for a long run the wire has to be much thicker than for a short run.Common house wiring for lighting circuits can be 12 or 14 guage.Wiring to supply a high-powered 240 volt kitchen range or clothesA dryer may have to be 4 or 6 guage but the actual size needed Always depends on the length of the run.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourselfon electrical circuits, equipment or appliancesalways use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
