0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why is the nozzle hole much smaller than the gas inlet in the gas burner?
The "gas inlet" hole doesn't just let in gas - it lets in gas and a large amount of air - the two together are needed for proper flame. Burning the gas "raw" makes a lazy, yellow, smoky flame.
Can the particles in gas be compressed into smaller volume?
Yes, a gas can be easily compressed.
What happens when you force gas into a smaller space?
it might explode if you put it in a smaller space.
Why is house heater running but blowing cold air?
Turn up the inlet gas pressure on the furnace to create more BTUs.
What happens to the pressure of the gas in the container?
The pressure increases if the container gets smaller or the gas heats up. The pressure decreases if the container gets bigger or the gas cools off.
What is the cut diameter in cyclone separator?
it is half the inlet mass of the gas
What is the function of the gas inlet and gas spud in the Bunsen burner?
In the gas industry, the process of beginning to drill a well. Initially a larger drill bit is used to drill a surface hole, which is lined with casing and cement to protect groundwater. After the surface hole is completed, the main drill bit is inserted and the well is drilled to the total depth.
Why is the nozzle hole much smaller than the gas inlet in the gas burner?
The "gas inlet" hole doesn't just let in gas - it lets in gas and a large amount of air - the two together are needed for proper flame. Burning the gas "raw" makes a lazy, yellow, smoky flame.
When a steadily flowing gas flows from a larger diameter pipe to a smaller diameter pipe what happens to its speed its pressure and the spacing between its streamlines?
When a steadily flowing gas flows from a larger diameter pipe to a smaller diameter pipe the speed of gas is decreased and pressure become increased and the spacing between the streamlines less and the streamlines come very close to each other.
What is the spud on a Bunsen burner?
it limits the supply of gas to the barrel.
Why the nozzle hole is very much smaller than the gas inlet?
The velocity of a fluid through a pipe is determined by the flow rate and the pipes diameter. If the flow rate remains the same but the diameter is reduced, then the velocity will increase. This means that the gas is able to travel a longer distance through rubber tubing without increasing flow and thus wasting gas.
Why is the nozzle hole is very much smaller than gas inlet?
This is to increase the velocity of the gas as it enters the rubber tubing. The higher velocity means it will travel farther in tubing while still remaining at low pressures.
What is the function of the Gas inlet of the Bunsen burner?
The inlet valve at the bottom is used to draw oxygen in from the environment so that the flame burns more efficiant and hotter. If closed the flame will be an orange colour and will leave a sooty deposit due to the gas not oxidizeing compleately.
When flowing gas flows from a larger diameter to a smaller diameter pipe?
The speed of the gas must increase. Also, depending on the geometry of the transition, it's comparatively difficult to maintain laminar flow, and there's typically considerable turbulence there and for some distance after.
What is the length of an blade for a gas turbine?
The length of a blade depends on the style (impulse or reaction), the overall size of the turbine, whether it is an axial flow or radial flow turbine, and where the blade is located within turbine of an axial flow turbine. One thing that is constant: the length of the blade increases from the steam or gas inlet to the discharge of the unit. The profile will gradually increase in diameter from inlet to discharge.
What is the function of hydrogen in an absorption refrigerator?
usually hydrogen or helium gas were choose as inlet gas/ carrier from evaporator to absorber coil. Inlet gas contribution toward total pressure in the system where according to formula to determine partial pressure in the system PTOTAL SYSTEM = P HYDROGEN (inlet gas ) + P AMMONIA (REFRIGERANT )
Comparration diameter size of suction and discharge?
The diameter of the discharge line leaving the ac compressor would be smaller than the suction line, because the compressed gas in the discharge line is more dense.
