0
What else can I help you with?
Where is the low pressure air conditioner connection on 2000 dodge ram 1500?
The low pressure port of the A/C system usually has a blue or black dust cap and is located either on the larger diameter metal tubing typically found between the evaporator and compressor, on the compressor itself, or on the receiver drier (orifice tube systems only). The high pressure service port is found either on the smaller diameter tubing or the compressor and is larger in diameter. Only charge through the low pressure port.
What is the diffence in diameter between the smallest and largest planet?
The smallest planet is Mercury with a diameter of about 4,880 kilometers, while the largest is Jupiter with a diameter of about 139,820 kilometers. Therefore, the diameter difference between the smallest and largest planet is approximately 135,940 kilometers.
What is the difference in diameter between Jupiter and Pluto?
The diameter of Jupiter is about 142,984 kilometers, while the diameter of Pluto is about 2,377 kilometers. Therefore, the difference in diameter between Jupiter and Pluto is approximately 140,607 kilometers.
What is the difference between stream lines and path lines?
Streamlines represent the instantaneous velocity field at a given moment, while pathlines show the actual path that individual particles follow over time. Streamlines provide information about the flow pattern at a specific instant, while pathlines depict the trajectory of individual particles as they move through a flow field.
Is there a relationship between a planet's diameter d its period of rotation?
No, there is not.
What happens to spacing between streamlines of gas flowing from large pipe to smaller pipe?
Pressure rises at the junction.
What is the relationship between pressure and diameter in a pipe system?
In a pipe system, there is an inverse relationship between pressure and diameter. This means that as the diameter of the pipe increases, the pressure within the pipe decreases, and vice versa.
What is the relationship between pipe diameter, pressure, and flow in a fluid system?
In a fluid system, the relationship between pipe diameter, pressure, and flow is governed by the principles of fluid dynamics. A larger pipe diameter allows for higher flow rates at lower pressures, while a smaller diameter results in higher pressures needed to achieve the same flow rate. This is known as the relationship between pressure drop and flow rate in a fluid system.
What is the recommended tire pressure for a rear bike wheel with a 700c diameter?
The recommended tire pressure for a rear bike wheel with a 700c diameter is typically between 80-130 psi (pounds per square inch).
Where is the low pressure port for ac on a 94 cavalier?
The low pressure port of the A/C system usually has a blue or black dust cap and is located either on the larger diameter metal tubing typically found between the evaporator and compressor, on the compressor itself, or on the receiver drier (orifice tube systems only). The high pressure service port is found either on the smaller diameter tubing or the compressor and is larger in diameter. Only charge through the low pressure port.
What is the relationship between the radius and the diameter of a circle?
The relationship between the radius and the diameter of a circle is that: radius = diameter /2
Location of high pressure AC port on 1998 c280 Mercedes?
The low pressure port of the A/C system usually has a blue or black dust cap and is located either on the larger diameter metal tubing typically found between the evaporator and compressor, on the compressor itself, or on the receiver drier (orifice tube systems only). The high pressure service port is found either on the smaller diameter tubing or the compressor and is larger in diameter. Only charge through the low pressure port.
Where is the low pressure ac service port on a 2001 silverado?
The low pressure port of the A/C system usually has a blue or black dust cap and is located either on the larger diameter metal tubing typically found between the evaporator and compressor, on the compressor itself, or on the receiver direr (orifice tube systems only). The high pressure service port is found either on the smaller diameter tubing or the compressor and is larger in diameter. Only charge through the low pressure port.
What is the difference between API 600 and API 602 valves?
The main difference between API 600 and API 503 valves is their port diameter. Also, the pressure testing between the two is different as well.
A spherical balloon of 0.5m diameter contains air at a pressure of 500kpaThe diameter increases to 0.55m in a reversible process during which pressure is proportional to diameter.Determine the work do?
To determine the work done during the reversible expansion of the balloon, we can use the formula for work done in a process where pressure is proportional to diameter. The initial diameter is 0.5 m, and the final diameter is 0.55 m, with initial pressure ( P_1 = 500 , \text{kPa} ). The average pressure during the expansion can be calculated as ( P_{avg} = \frac{P_1 + P_2}{2} ), where ( P_2 ) can be found using the proportional relationship. The work done ( W ) can then be calculated using ( W = P_{avg} \cdot \Delta V ), where ( \Delta V ) is the change in volume between the two diameters. However, without calculating the new pressure ( P_2 ), we cannot provide a numeric answer. If you want, I can further assist with that calculation.
Low side ac port on a 1993 Seville?
The low pressure port of the A/C system usually has a blue or black dust cap and is located either on the larger diameter metal tubing typically found between the evaporator and compressor, on the compressor itself, or on the receiver drier (orifice tube systems only). The high pressure service port is found either on the smaller diameter tubing or the compressor and is larger in diameter. Only charge through the low pressure port. The high pressure charging valve is located either on the high pressure line or the muffler, and the low pressure charging valve is located either on the accumulator or low pressure line.....
What is the difference between a radius and a diameter?
a radius is half the diameter of a circle
