0
Furnace oil is mainly measured in centistokes (cST). It could vary frm 0-1000 cSt. It basically means the quality of furnace oil used in your application process. For eg. In Furnace oil boiler its mostly recommended at 125 cST grade to be used. The better the furnace oil the better its is for your equipment giving less maintenance cost and saving energy in process. There are other factors like pour point, flash point, etc which are also major factors in furnace oil and would be available with your furnace oil supplier.
What else can I help you with?
What is the density of premix asphalt per metric ton?
The density of premix asphalt typically ranges from 2.2 to 2.4 metric tons per cubic meter. This means that 1 cubic meter of premix asphalt would weigh between 2,200 to 2,400 kilograms. To calculate the density per metric ton, you would divide the density range by 1,000, resulting in a density of 2.2 to 2.4 metric tons per cubic meter.
What is the density of Piece of Heart from Ocarina of Time per cube meter in kilograms?
The density of Piece of Heart from Ocarina of Time is in the 2.0 to 2.7 grams per cubic centimeter range, (2000-2700 kg per cubic meter)
What is the density of raw sewage?
The density of raw sewage can vary widely depending on its composition and the presence of solids. On average, it can range from 1,010 to 1,050 kilograms per cubic meter.
How hot should a furnace be?
It depends on the type of furnace and the manufacturer.
Will a 3250 watt generator power older a gas furnace?
A 3250 watt generator has the capacity of I = W/E, 3250/120 = 27 amps. This should be in the range to operate any gas furnace.
What is the weight of 1 cubic meter of granular crushed material?
The weight of 1 cubic meter of granular crushed material can vary depending on the density of the material. On average, it can range from 1.5 to 2.4 metric tons. It is important to know the specific density of the material to calculate its weight accurately.
Why should voltage be determined using highest range available first?
To keep from cooking your meter.
What the density of wmm?
The exact density of WMM (Wet Mix Macadam) can vary depending on factors such as aggregate size, moisture content, and specific composition. However, a typical range for the density of WMM is around 1.8 to 2.2 tonnes per cubic meter.
How do you find the density of oil?
Mathematically, density, mass and volume are related according to the following formula: ρ=m/V where ρ=density, m=mass and V=volume. The density of most oils will range between 700 and 950 kilograms per cubic meter (kg/m3).
How much weight of sand per m3?
The weight of sand per cubic meter can vary depending on the density of the sand. Generally, the density of sand is around 1,600 kg/m3 to 1,900 kg/m3. This means that for a cubic meter of sand, the weight can range from 1,600 kg to 1,900 kg.
What is the typical cost of replacing a furnace heat exchanger?
The typical cost of replacing a furnace heat exchanger can range from 500 to 2,000, depending on the type of furnace and the complexity of the installation.
Can only find 1 gas cut off vavle in my 1986 home it's located by the fireplace there is an outlet for a gas range but no cutoff valve is the gas to the house controlled by the 1 valve?
Your use of the term 1986 home suggests you have a mobile or modular home. If so, there should be a shut off at each gas appliance. Stove, furnace, fireplace. If not, there may be one outside between the house and the meter. If not, there is one on the meter. If you have a regular house that was built in 1986, there should be a main shut off in the basement. If you do not have a basement, then it is probably only at the meter.
