0
If you are using the type with the nylon insert, that part goes out. You should be able to put the nut on by hand until you reach that part. Some nuts lock on with depressions on the sides of the nut. These type it doesn't matter which side you start with.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Ive got a rusty holding your tank to your toilet and you need to replace it cause it is leaking and you cant get the nut off the bolt What is the best way?
spray WD40 ON IT
How do you tighten an aircraft nut?
The same way you tighten any other nut. Use the appropriate tool to the recommended specifications.
What are the dimensions of a skateboard truck. I mean all the holes sizes spaces between them tread sizes nut and bolt and and please specify the dimensions of the base plate and hanger separately?
they are all the same, the only way to get dimensions is to go to your favorite truck's website.
Does the crankshaft nut trun left or right to loosen?
AnswerLeft, counter-clockwise. Lefty loosey, righty tighty. --------------------------------------------------------------------------------It depends on which way the crank rotates. If it rotates clockwise the nut will be threaded on counterclockwise to prevent it from loosening. If the crank rotates counterclockwise then the nut will be threaded on clockwise.
Which tool is sometimes called a nut driver it is used to tighten nuts is the some way that a screwdriver tighten screw?
A wrench is used to tighten nuts. Socket wrenches are a type of nut driver.
The best way to remove a ceased rear hub nut on a ford fiesta?
The nut used on the rear hub is a locking nut. With some muscle it will back off. It is advised not to reuse that nut.
How do you change blade in challenge mitre saw?
They usually have a pin or locking knob, you either push it in or hold it in while you loosen the blade retaining nut, some you might have to remove the shield or guard, older saws might not have this feature at all, place a piece of wood on the bed of the saw and hold down so the blade digs into the wood and loosen the nut.
How do you remove bolts on small pulley of water pump?
The best way is to "double nut" them. Thread one nut halfway down the bolt, then thread another down against that one. Use a wrench on the first (bottom) nut to back the bolt out.
Where on aircraft locking wire is used?
All over the place! Seriously locking wire is used for so many applications. Especially larger aircraft.Every piece of hardware (nuts and bolts) on aircraft has to have 2 locking 'mediums'the first kind is torque up the nut and bolt, or whatever it is.usually, the second kind of locking medium (called nylocks) is nylon in the nut, which grips the bolt, to a minimum of approximately 20 inch pound of force required to remove it.there is also 'metal lock' nuts, that work in the exact same way, by using deformed metal to hold the nut in place.lockwire is used when it is not possible to use either of the above methods.so lockwire is used on bolts that may go into engine blocks, filter bowls, and places around extreme heat, like engine bays. Also large diameter bolts,
How do you fill a large hole in a wooden headboard so that a socket screw can be placed in that hole?
One way is to use a combination of washers bigger than the hole that the bolt can tighten against. You might have to get a slightly longer bolt, but all you do is take it with you to a hardware store and match it up or get a new nut and bolt that will fit through the headboard. .
How do nylon lock nuts work?
Nylon locking nuts, also known as ny-locks, have a small ring of nylon one one end that forms slightly smaller hole than the threaded hole going through the nut. When the nut is screwed onto a bolt, the bolt has to force its way through the smaller opening, causing the nylon to stretch. This stretching creates a huge amount of friction between the nut and the bolt, allowing the nut to stay tight for long periods of time without coming loose. Nylon lock nuts are especially useful for applications that involve a lot of vibration that would cause regular nuts to come loose.
1991 Mercury Capri power steering AC belt won't come off Loosened locking nut and adjusting bolt beside power steering pump all the way and belt is still too tight to come off What next?
If you pull the bolt next to the oil dipstick out of the power steering unit it will give you plenty of slack to get the belt off.
What is the lug nut size on a 2000 Honda Civic?
It is probably a 19mm. The best way to find out is to go to the parts/hardware store and thread the lug nut onto a bolt and which ever size bolt it fits that will be the size of the lug nuts.
What is the best way to remove a tight bolt or nut?
Spray it with a penetrating oil leave it for a few hours then try to loosen it, or heat the nut up quickly and try to remove it then.
What way do paddock bolts go for a horse?
You will want to put the smooth side of the bolt on the inside of the paddock with the nut on the outside.
Which way do you turn the bolt on the fan to take off?
The big 1 and 7/16" nut turns counterclockwise to remove it.
What is short bolting?
Short bolting refers to a situation in rock climbing where a bolt is placed too close to the ground, making it difficult for the climber to clip their rope into it safely. This can create a dangerous situation where a fall from above the bolt could result in a ground fall.
