0
Did you find out? I know they are plastic, but they can be made out of different types of plastic. I need to know what type. If I find more out, I will edit the answer again.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Why are plug sockets covers made of plastic?
If they were metal and the live had somehow come loose and was touching the casing, it would make the plug case live too. However electricity does not flow through plastic because the electrons can't pass.
Will wet coils dry out and work again?
coils are sealed except for the terminal were the plug wires are installed. with plug wires properly installed on these terminals you should be able to spray the coils with water while it is running and have no problems with an engine miss or arching of electricity. if it is missing when wet around the plug wires and arching is present then the wires should be replaced, if it is arching anywhere else then the coil casing could be cracked and should be replaced.
What do the timing marks on a mercury topaz 1988 4 cylinder look like?
There is a little window on the fly wheel housing. when open you will see small lines inscribed on the casing. If you turn the engine by hand you will see the mark on the flywheel. Usually you use a white chalk to the line on the flywheel and the mark on the housing. With a timing lite on the number 1 cyl. you will see the marks where they line up. Adjust with the dist. to what you want, but first un-plug the wire harness at the bottom of the dist. before you can check the timing. The plug will be at the lower end of the dist. just to the right.
Wide blade black or white 110 volt plug?
white. Screws on that side (neutral) should be silver. "Brass" side gets the Black (hot) wire.
How is a three pin plug assembled in production?
black = HOT White = Neutral (current carrying) Green = Ground
What is the white casing on a plug?
Plastic Lol
What is the casing of an electric plug made of?
ABS
What is the casing on a 13 amp plug made of?
They are usually made of a plastic called urea-formaldehyde.
Where is plug on 2001 Jeep Wrangler manual transmission?
look about mid way on the transmission, on the drivers side, the drain plug will be on the bottom, and the fill plug will be half way up the casing right above it.
Why are plug sockets covers made of plastic?
If they were metal and the live had somehow come loose and was touching the casing, it would make the plug case live too. However electricity does not flow through plastic because the electrons can't pass.
How do you remove the radio 1997 Mazda 323?
First remove the outer casing the thin black plastic strip around the outside of the radio, you do this by pushing in 2 plastic hooks at the top and bottom. now look below the radio on the dash you will find 2 philipshead screws holding the plastic casing around the radio. remove these and also the plastic casing. on the underside of the radio is a metal dock with screws on either side of the unit. remove these 4 screws and slide the the unit forward remove the plug in the back of the unit. discard radio and plug in the new CD player repeat the steps above in reverse.
Where is Oil drain plug location on a 2007 harley-davidson sportster 883?
The oil drain plug runs out of your oil tank and down through the casing that houses your transmission, it is located in the middle of the casing, in between the frame rails. It has a black plastic plug in the goodyear rubber hose. You will need a flat tipped screwdriver to loosen the clamp that holds the plug in. It is pretty much in line with your kick stand if you have your bike leaning on it.
When the switch button fails how do you bypass motorcycle ignition wire?
If you have broke your ignition switch or lost the key disconnect the ignition barrel from the white connector plug then pull off the the key hole then with a knife peel back the casing around the wires to bear metal and wrap them together and attach the ignition back and it should be like turning the key.
Where do you hook the rubber tube coming out from the top of the transmission sub casing on a ford contour 1998?
If it's an automatic, this is likely the transmission breather tube, it should reach up and hook to a clip right around the battery tray, do not plug it.
How do you put a spark plug in?
you get a spark plug socket or one of similar size to fit the spark plugs, then you just put it in the correct location and screw it in snuggly(not too tight cause you will break the ceramic casing), then connect all the spark plug wires
Where is the governor on a Yamaha razz 50 cc moped?
Take off kick starter, located on the left side rear. Then take all the screws out of the black casing that the kick starter is attached to. SAVE THE NUT FOR LAST, all of the oil comes out. Take off the casing, and then the governor will be on the pully closest to the front of the moped, there will be spring type things around it. Take off the nut in the center of that, and then one of those washers (im not sure which one) is the governor. Take it out, and re assemble everything. Make sure everything is nice and snug, and be sure to put oil back into the white plug located on the rear of that black casing that the kick starter comes out of.
How do you change oil filter on 2001 mondeo tdci?
Remove the plastic undertray from underneath the engine, and undo the plug bolt in the sump to allow the oil to drain out. Clean the oil filter (located in the front of the engine) and use an Allen key in the small plug in the centre of the bottom cover to remove the plug, allowing the filter casing to drain. Refit the plug into the filter casing, then use a 36mm socket to unscrew the filter cover and remove the paper element. Fit a new element and sealing ring, and reassemble in the reverse order :)
