0
What else can I help you with?
What is the drive cycle for a 96 Kia Sportage?
How do I do my own version of a Drive Cycle for a 96 Kia Sportage? My Monitors are not ready for my smog check to pass thanks Margaret
What is the drive cycle for a 2001 Dodge Ram 1500?
drive cycle for 2001 dodge ram 1500
1998 Saturn emissions testing did not fail but will not pass no trouble codes are listed catalytic converter eff evaporative control system egr flow qxygen sensor all show not ready why?
I am facing the same problem and it has to do with drive cycle that no one knows. The computer must calibrate the sensors for a certain period of time during driving. Saturn will do it for around 90 but will not tell how.
How do you pass vehicle inspection for 97 Honda accord ex V6 motor when test says status not ready?
You need to run the car through it's drive cycle before the computer can perform all of it's emissions tests. Look up the drive cycle specified by Honda, perform the drive cycle, and then it should be all set.
How long is a drive cycle on a 1996 Mazda b2300 you have driven 600 miles since everything was reset not ready for smog yet please help?
Have a scanner determine which item(s) is not "ready" yet then repost.
What would make the catalytic converter be not ready for inspection?
The system probably hasn't completed its drive cycle. The year, make and model info would help us.
What is ready drive?
your butt
How do you turn off the check engine light on a Honda S2000?
Two parts to the answer - theory first - Fix problem and then drive car through a "drive cycle". The sensors are checked on a periodic schedule by the computer. Drive cycle is the number of miles driven it takes for the computer to do the next check on the sensor related to the repair. I do not know the miles for the s2000, but typical is 100 miles. Part 2 - If passing inspection is the issue, the auto parts house can reset your light with their computer code reader, but the computer will not show the sensor in question as "ready" until the repairs are made and the drive cycle is complete. In most states, the computer must show "ready" in all categories to pass inspection.
How do you reset obdII drive cycle for 2003 Mercedes Benz S500?
To reset the OBDII drive cycle for a 2003 Mercedes Benz S500, you typically need to clear the diagnostic trouble codes (DTCs) using an OBD-II scanner. After clearing the codes, perform a complete drive cycle, which usually involves a series of specific driving conditions such as idling, acceleration, and deceleration under varied speeds and loads. It's important to follow the manufacturer's specified conditions for the drive cycle to ensure all monitors are reset. Finally, check the system with the scanner to confirm that all monitors are ready.
How do you force a menstrual cycle?
You can't force your menstrual cycle, it will start only when it is ready to do so. You can't force your body to ovulate and thus to menstruate until it is ready.
What is the drive cycle to reset not ready tests on a Mazda MPV?
To reset the not ready tests on a Mazda MPV, you typically need to complete a specific drive cycle. This usually involves driving the vehicle under varied conditions, including idling, steady speeds, and acceleration. A common cycle includes driving at a steady speed of 25-45 mph for several minutes, followed by deceleration and idling. It's important to ensure that the engine reaches normal operating temperature and that all systems are exercised to allow the onboard diagnostics to complete their checks.
What is a drive cycle to reset 'not ready' tests on a Mazda 6?
A drive cycle to reset 'not ready' tests on a Mazda 6 typically involves a series of specific driving conditions to allow the vehicle's onboard diagnostics (OBD) system to complete its self-checks. This usually includes starting the engine and letting it idle, then driving for a short distance at varying speeds, including city and highway driving, while allowing the engine to reach its operating temperature. It's important to ensure that the vehicle goes through both acceleration and deceleration phases. Completing this cycle helps the OBD system to run the necessary readiness tests and potentially reset the 'not ready' status.
