0
you are beautiful just your bald head just makes Aaron want to hug you.
By Aaron Albert
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What should the amp reading be Amp on 11kw motor - no load?
hi.. this is pankaj working as power engineer. we have a 11 kw induction motor which is used in fluidising blower. its no load current i sarround 9.5 to 10.6 amp. and under load its ampere does nt exceed 15 amp. its winding resistance is 1.4 ohm.
What does Windows NT stand for?
New Technology. So when you see 'Uses Windows NT Technology' advertised, it reads 'Uses Windows New Technology Technology!'
What is theory of swinburne's test?
swinburnes test is a type of SWINBURNE'S TEST:- Ø It is a simple method in which losses are measured separately and from their knowledge, efficiency at any load can be pre-determined in advance. The only running test needed is a no load test. Ø Swinburne􀂶s test is applicable to those machines in which flux is practically constant i.e. Shunt wound and Compound wound machines. Ø The machine is running as a motor on no-load at its rated voltage and its speed be adjusted to its rated value using Shunt regulator. Ø The no-load armature current Iao is measured using an ammeter, where as shunt field current Ish is given by another ammeter. The no-load input current is given by Io = Iao + Ish Ø Let the supply voltage be V volts N o -l oa d i nput = V Io watts P o w er input to armature = V Iao watts P o w er input to shunt = V Ish watts No-load input supplies Copper losses (Armature & Field), Iron losses (Hysteresis & Eddy current) & Mechanical losses ( Friction losses & Windage). Constant losses = No load input power 􀂱 Armature copper losses Wc = V Io - Iao² Ra watts . Ø Predetermination of efficiency of a motor at any load Input = V I w at ts. Armature Cu losses = Ia 2 Ra C o n st a nt losses = Wc T o tal losses = W c + ( I - Ish)² Ra
How and why do you do a load test on an induction motor?
This was a good experiment in terms of it was to show us the direct result of the effect of increasing the load current on the motor power factor. It showed that the higher the current the better the power factor. The Electrical Supply Board desire a high power factor for installations within Ireland and penalise those which do not meet required standards as they see poor power factor as a wasteful loss of energy. It also showed that there are two ways in which the rotating magnetic field could be used to provide the rotating motion.
What does NT stand for in money?
It stands for the New Taiwan dollar.
What should the amp reading be Amp on 11kw motor - no load?
hi.. this is pankaj working as power engineer. we have a 11 kw induction motor which is used in fluidising blower. its no load current i sarround 9.5 to 10.6 amp. and under load its ampere does nt exceed 15 amp. its winding resistance is 1.4 ohm.
Does a load get applied to 401k rollover?
Mine did`nt in 2004
What is the meaning of NT?
Light Motor Vehicle - Non Transport
Does windows NT need DOS to run?
No.
What is the meaning of LMV-NT?
Light Motor Vehicle - Non Transport
What is the meaning of LMV NT?
LMV-NT" (Light Motor Vehicle - Non Transport) license is used to drive light motor vehicles such as car, jeep, small vans for personal purposes, but not for commercial transportation.
K n o ht g t g aj NT s s h?
k___n__o __h__t___g__t__i__a j__nt__ s___ s__h__
How windows NT run process that run on different OS?
Windows NT run processes that run on different operating system i.e. Linux, OS/2, and Solaris, because all mentioned operating systems support multi-threading in single process. while in those OS which don't support multi-threading single process (e.g. UNIX) windows NT processes don't run on them.
How do you pass level 18 on run 2 on coolmathcom?
nt kne
Can you load Microsoft office windows NT and windows 98 on a windows xp system?
http://www.squidoo.com/howtofixthewindows7build7600
Does DC motor run at a varying speed?
only shunt dc motors have varaible speed control. compound dc motors do however NT as much, plus they are just a mixture of series and shunt dc motors.
How do you load hal.dll in MS-DOS?
You don't. hal.dll is a Windows NT file; it isn't usable or needed in MS-DOS.
