0
i also want to know the answer....
thanks in advance
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Connecting rods are normally made of what steel?
They are made from haevy steel to maintaint the effectivnes and the strenght of the connecting rod. When the compression accures in a combustion chamber pushehs the piston down and the connecting rod. They need to be strong otherwise they will crack and the engine will blow up.
Where are bevel gears used?
They are used when the angle of rotation needs to be changed. The rotation of a vertical rod can be changed to rotation of a horizontal rod by the use of beveled gears. <><><><><> bevel gears ARE two the wheels together or just two two wheels so pretty much you can find bevel gears in objects like .... can opener cars in a hand drill.. and many more
How the angle and speed effect weld joint?
The angle of the torch or tungsten electrode like that used in Tig welding , or the MiG stinger, or any consumable rod like that of a 7018 rod used in SMAW welding. All run a little bit cooler of a puddle of molten metal when held at an angle. When feeding rod material into a vertical joint going in the upwards direction this lends it self to better fill and penetration in the joint. More filler rod is going to be deposited into the weld joint going in the upward direction then if one is welding in the downward direction on a vertical pass on any piece of material, also at an angle the puddle is a going to run a little cooler. When the electrode, stinger or torch is held directly held over the base material this changes the molten pools temperature to a slightly higher temperature .when holding a gas flame torch and using the back handed method the enveloping surrounding flame helps keeps the material's temperature higher in the weld joint area, that was just welded, higher temps after the welding process to allow for slower cooling,which can have a beneficial effect. When the Speed or feed rate of the welding rod or wire is feed to fast into the molten puddle or the movement of the rod, stinger or torch is feed to fast across the material to quickly and the delutement of the rod into the base material and the welds surrounding area around the weld bead will then be an incomplete or cold weld it will form on the base metal, which can leave undercut or lack good fusion or good penetration a poor weld is typical, this is not the desired result. When welding is performed by the human hand, one should not speed through the welding process , focus and care on the molten puddle and its conditions during the welding process and being certain of good penetration is more important then how fast one welds.
How do you remove a piston?
Easy way is to remove the cylinder head and the oil pan. Then unbolt the cap on the lower side of the connecting rod, then slide the piston out of the top of the engine where u removed the head. Its alot more work than most people think.
A stiff rod that rotates around a pivot point?
A stiff rod that rotates around a pivot point is called a lever. It is a type of simple machine that is used to help move a heavy or firmly fixed load.
What is difference between piston rod and connecting rod?
A connecting rod connects the piston to the crankshaft - A piston rod (also called a wristpin)connects the piston to the connecting rod.
What type of material is used in the connecting rod?
forged steel
What is a rod bearing?
Rod bearing (short for connecting rod bearing) Is the bearing where the connecting rod is attached to the rotating crankshaft.
What is a rod journal?
Connecting rod journals are the part of the crankshaft where the connecting rods attach to. There is one rod journal for each piston/connecting rod in the engine. These journals have a machined surface so the connecting rod bearings can move smoothly as the crankshaft rotates.
Function of a connecting rod of an ic engine?
In a reciprocating engine, the connecting rod is used to connect the piston to the crankshaft. It converts the linear motion (reciprocating motion) of the piston to the circular motion of the crankshaft.
Connecting rods connect the piston to what?
The connecting rod has a "wrist pin" which goes through the side of the piston and through the connecting rod. It is one of the most critical fit parts of an engine.The connecting rod or con rod connects the piston to the crank or crankshaft!!!
What is the connecting rod and head torque specs on a GMC Sierra?
what is the main and connecting rod for a gmc 2.2l
What connects the con rod to the piston?
The connecting rod has a "wrist pin" which goes through the side of the piston and through the connecting rod. It is one of the most critical fit parts of an engine.The connecting rod or con rod connects the piston to the crank or crankshaft!!!
What is a fork connecting rod?
A forked connecting rod is where two connecting rods and there pistons are connected to one crankshaft journal as is the case of the old side valve ford v 8 engine but i believe this practice is still used to-day----------------jim
How many degrees of difference are there between the throw of one connecting rod and the throw of adjacent connecting rod?
80
Can the connecting rod have a small groove an still be ok?
Any damage on a connecting rod means it must be replaced!!!
How to connect connecting rod with piston?
You need a hydraulic press to press the pin into the piston and through the connecting rod
