0
The metal will melt if you do that.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Why is a bulb most likely to fail when the current is first switched on?
Light bulb filaments glow rather than burn because of the lack of oxygen within the vacuum of the bulb. Over time, the heating and contracting of the filament and the glass surrounding it creates a leak in the base of the bulb causing the vacuum to be lost and allowing oxygen to enter the bulb. It is during the contracting phase, which happens as the bulb cools after being turned off, that eventually the seal is lost. When this happens, oxygen is allowed to enter and the next time the bulb is turned on, the filament, now exposed to the oxygen, burns out.
What is the thin coil of wire inside a light bulb called?
If you are talking about an incandescent light bulb then its called a filament. It is thin so that it has a high level of resistance. Current going through the filament causes it to heat up and give off EM radiation in the spectrum of visible light.
What parts of a light bulb are conductors or insulators?
The conductors are the two wires you see supporting the filament. The glass supporting all this is an insulator. The metal ring around the base and the very bottom of the bulb conduct the electricity into the bulb. The plastic between them is an insulator. --- In incandescent bulbs, the filament of the bulb is a conductor, but has a high resistance to the flow of current, causing it to heat up and glow. In fluorescent bulbs, the gas in the tube resists the flow and is ionized. The ultraviolet photons that it gives off cause the inside of the tube (coated with phosphors) to glow.
What happens when a battery light the light bulb?
When the switch is turned it completes an electrical circuit. The circuit amperage flows through a high resistance filament in the bulb and it starts to glow. The bright glow from the filament and the reflector behind the bulb is what creates the flashlights beam.
What are some things that could burn at 900 C?
The temperature of 900o C is very high; pretty much everything than can burn, will burn, at that temperature.
Why do you use Argon in a light bulb instead of oxygen?
The current flowing through the filament causes it to heat to a very high temperature - so high that is becomes incandescent (glows) and gives light. If the bulb was filled with oxygen then, at those high temperatures, the filament would oxidise - burn out - and the bulb would be "blown".
Why does the filament in a light bulb not burn up immediately?
The 'Filament' of a lightbulb is a peice of metal with an unusually high melting
Why is argon used instead on air in the light bulb?
The filament in the light bulb is heated to a very high temperature. At such a temperature oxygen from the air would oxidise the metal(s) in the filament and thereby destroy the bulb. Using an inert gas such as argon in the bulb prevents such oxidation.
Why tungsten filament bulb is preferred in stefan's law experiment?
because it has high meting point to withstand high temperature.
How bulb light?
An electrical current is passed through the high resistance filament in the bulb, causing it to become white hot and so give off light. The inside of the bulb is filled with an inert gas, such as nitrogen, so the filament does not burn up .
How the bulb light?
An electrical current is passed through the high resistance filament in the bulb, causing it to become white hot and so give off light. The inside of the bulb is filled with an inert gas, such as nitrogen, so the filament does not burn up .
What will happen if a light bulb gets too much electricity?
If its an incandescent bulb the filament burns out; depending on the voltage put through the bulb (and the operating voltage of the bulb) the results can be quite spectacular. Normally the filament will burn out with a bright flash, if the voltage is high enough the bulb may explode.
What happens to the filament if the bulbs becomes brighter and brighter?
The bulb gets brighter because the filament is getting hotter. If the filament's temperature gets too high it will melt at some point and fall apart. The current will stop flowing and the bulb will "blow".
Which has the thickest filament - a high-resistance or a low-resistance bulb?
A low resistance bulb has a thicker filament.
Why does argon's electronic structure allow for better use in a light bulb?
Argon is inert. This means that the filament in a light bulb can be heated to a high temperature in an environment where it will not react with the surrounding gases.
Why is there argon gas in the light blub and not air?
The hot filament of a light bulb would quickly burn away if it came in contact with oxygen from the air. Argon is inert and so will not react with the filament, even at extremely high temperatures.
Why is a bulb most likely to fail when the current is first switched on?
Light bulb filaments glow rather than burn because of the lack of oxygen within the vacuum of the bulb. Over time, the heating and contracting of the filament and the glass surrounding it creates a leak in the base of the bulb causing the vacuum to be lost and allowing oxygen to enter the bulb. It is during the contracting phase, which happens as the bulb cools after being turned off, that eventually the seal is lost. When this happens, oxygen is allowed to enter and the next time the bulb is turned on, the filament, now exposed to the oxygen, burns out.
