0
Why do you need to wait until the surface of a soldered joint goes dull before moving it?
Wiki User
∙ 11y ago
Yes, you should wait until you see a film cover the liquid silver colour of the connection
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is married Joint in Electrical?
The married joint is an electrical joint used for joining multi-strand cables. The wires are unstranded, then interlaced with the wires of the other cable, and then married (twisted) together before finally being soldered.
With regard to soldering what are the origins of the phrase tin-the-leads?
Tinning is a process of coating leads or other component parts with solder before making a soldered joint. It is done to ensure that the surfaces to be joined will have a good adhesion to the solder to ensure a robust and secure joint. If leads are not tinned before hand, there is a risk of a dry joint - a joint that might appear to be good but in fact does not have solder in intimate contact with the component. Most dry joints have an appearance that exposes the fault but not all do. The term tinning is used as tin is a component of solder (traditional solder is a mix of tin and lead). Tinning now usually means applying solder as described above but it can also mean applying a coating of tin without lead. Using pure tin is rarely if ever used today. Worldwide there is a move to eliminate lead from electronic assemblies and so tin/lead solder is being replaced. Tin is still used but mixed with copper, silver, zing and other more exotic metals. The process of tinning still takes place even with the new lead free solders.
What do you mean by electrical double wrapped cross joint?
An electrical double wrapped cross joint is just like an ordinary cross joint but double wrapped with electrical tape. It is used where two tap conductors need to extend away from the branch conductor in the opposite direction and is stronger than the ordinary cross joint.
What is plain top joint?
ahmbot
What is a dove tail joint?
It looks like the tail of a Dove.
Do soldered joints have too high a resistance?
Soldered joints will have a higher resistance if the joint is not a clean solder joint. Badly soldered joints are classed as a cold solder joint. <<>> ...for what? Application matters here.
What is a bad solder joint?
A soldered joint that was done poorly.
What is married Joint in Electrical?
The married joint is an electrical joint used for joining multi-strand cables. The wires are unstranded, then interlaced with the wires of the other cable, and then married (twisted) together before finally being soldered.
What is a plumber's joint?
Lead and oakum "caulked Joint" Welded Joint, lead wiped, lead burned, brazed, soldered, mechanical (MJ) joint, flanged joint, screwed joint, compression , flaired
What is the purpose of using soldering flux?
After cleaning copper pipe and fitting, applying flux helps ensure that solder will adhere to pipe and fitting when joint is heated to proper temperature.AnswerIt depends on what type of 'flux' you are talking about? For example, 'electric flux' and 'magnetic flux' exists naturally, and is not 'for' anything in particular, although it can be made use of.
Is diarthrotic joint is a freely moving joint?
Yes
What is the purpose of solder flux?
Very simply flux reacts with surface corrosion and washes it away, making the metal surface being soldered easier for the solder to wet and producing a more solid and reliable joint, both mechanically and electrically. Acid flux is more aggressive and acts faster than rosin flux, but must be washed off completely with water as soon as the joint cools because the acid will slowly attack the metal of the joint. As electronic circuits usually should not be washed with water, only rosin flux should be used on electronics because it can be left on the completed joint without damaging it.
Does a bad CV joint make a noise when car in neutral?
Yes it does if the car is moving. Because the CV joint is part of the axil if the car is moving the bad CV joint will be moving too. or No it will not make noise if the car is in neutral and the car is not moving.
What Convex and concave rule of the joint?
When a concave surface is moving the roll and the glide occur in the same direction and that when a convex surface is moving the roll and glide are opposite. Here's an example: If the tibia moves on the femur since it is a concave surface it is said the glide is anterior only; however, is the motion is closed chain and the femur is moving on a stationary tibia then the femur which is a convex surface glides posterior and rolls anterior on the tibia's plateau. hope this helps!
Can you tell if rubbing or grinding noise is transmission or cv joint?
If you aren't moving and it is making the noise, it may be the transmission or engine. if you are moving and it makes it, it could be a joint or a worn disc brake. If you aren't moving it is definitely not a joint.
What is articulating surface?
joint
What is the ovoid joint?
an ovoid joint is also called a condyloid joint. It is when one surface is convex and one surface is concave. Example: wrists and proximal knuckles
