answersLogoWhite

0


Best Answer

the speed might be related in three ways - either the wind speed under the vehicle is creating a draft that is pulling on the wire or the engine mounts are collapsing and the engine is moving about with an increase in speed or the increased vibration at higher speeds is loosening the wire. Assuming the problem is not collapsing engine mounts the wire should not be affected by either draft or engine revs and the fact that it is coming off means it probably needs replacing. I am assuming by spark plug wire you mean the spark plug lead not the cap on the plug itself. if the cap is coming off it could be the spark plug is not tight and the cap is being blown off or just that the cap is aging and does not clamp on tightly anymore.

User Avatar

Wiki User

16y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Why does my spark plug wire pop out when I go too fast?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Why does the spark plug wire pop off the spark plug on a 91 jaguar xj6?

you're not getting it seated all the way. the clip has to snap onto the top of the spark plug.


How do you remove spark plugs on boulevard cruiser?

Pop the hood open, remove the filter to the carburator, remove 1 spark plug wire boot at the front right side while facing the engine, remove the spark plug, add the new spark plug as well as the spark plug wire boot.


How do you remove the spark plug wire from the spark plug a 2002 Toyota tacoma?

Spark plug wires have caps that fit on the plugs. They just pop off and on. Make sure the motor is cool when you take it off. You'll get burned if you don't from the heat of the engine! Just grap the cap, not the wire, and pull it off.


Why do sparkplug wires pop off?

They have to be able to be removed so you can replace them. If you are asking why a spark plug wire would arbitrarily pop off the answer is simple you have case of tinkeritis and you should leave it alone.


How do you check plug wires?

How to Check a Car's Spark Plug Wires By eHow Cars Editor Part of car overhaul and car maintenance is checking your car's spark plug wires. These cables connect the spark plug to the distributor. You must check them every year and replace or clean them as needed. Always replace the entire set even if only one wire shows signs of wear. Difficulty: Moderately Easy 1. Turn off your car engine to overhaul your spark plug wires. Let your car cool down. Open the hood of your car and look inside for your spark plug wires. 2. Find the distributor. You will see several cables going across and ending at the individual spark plugs. These are the spark plug wires. 3. Remove one spark plug wire at a time for better inspection. Pop it off the spark plug and the distributor. Remove only one wire at a time. This will ensure you do not mix up the spark plug wires. 4. Look at the wire carefully. If it has any tears or cracks, you must replace it now. Always replace all spark plug wires at the same time even if only one needs replacement. 5. Clean a dirty spark plug wire. Use hand cleaner soap and wipe completely dry. Reinstall the spark plug wire into the distributor and connect to the spark plug. 6.Repeat this overhaul at least once a year. Remember to check the spark plug wires when you change your spark plugs. Tips & Warnings · Do not remove all of the spark plug wires at one time unless you are very sure you know which one goes where. If you mix them up, your car will not run. Remove one at a time then replace or reinstall it. Move on to the next one.


As a novice is it fairly easy to change the spark plugs and wires on a 1996 Mazda 626?

how to change spark plugs and wiresi found this while surfing the internet trying to find out why my 1994 Mazda 626 misses while running hope it helps IntroductionA bad spark-plug wire can keep your car from running well or starting at all. You should replace the spark-plug wires every 30,000 miles (50,000 km), although a tune-up won't necessarily include this service. Unless you have asked for them to be replaced, your car's spark-plug wires may be quite old. InstructionsDifficulty: Moderately Easy Steps1 Step OnePurchase a set of spark-plug wires at an auto-parts store. It is also possible to buy a single wire if only one needs replacing.2Step TwoClick to enlargeLook under the hood to find the spark-plug wires.3Step ThreePull off one spark-plug wire at a time by grasping it at the base of the wire. Use a spark-plug wire puller or just your fingers.4Step FourMatch it up by length with a new plug wire. Each spark-plug wire is a specific length, so make sure to replace the wire with one of exactly the same length.5Step FiveAttach the new wire to the spark plug on one end and to the distributor cap on the other end. Listen for a small click or pop as you connect the wire.6Step SixRepeat steps 3 through 5 for all the other plug wires.7Step SevenReplace the coil wire (if your car has one). This is the wire that goes from the middle of the distributor cap to the coil. Use the same method as for replacing the other plug wires.


How do you change a spark plug?

Without more information about the type of engine, and the vehicle it is in, all you can expect to get is generic information. Generally, with the engine cold. You need to remove the spark plug wire from the plug, twisting while pulling on the "boot" not the wire! Next find the correct spark plug socket,(one that the new spark plug fits into, AND holds the spark plug. Now make sure the place that the old spark plug is screwed into is clean, using compressed air blow out around the old spark plug to keep dirt and sand from falling into the cylinders (scoring/scratching the life out of them!) Using a 3/8" drive rachet, an extention and the spark plug socket, put the socket in the hole that you removed the spark plug wire from and turn the socket counter clockwise until the spark plug is free. Inspect the spark plug for unusual wear, or deposits this could be a sign of engine problems. Take the new spark plug check the gap!! if it is correct place it in the socket and start theading it in the spark plug hole by hand, turning it clockwise. Tighten the plug firmly, but not till all the veins pop out of your face. Reinstall the sparkplug wire you should feel it snap onto the end of the spark plug. Continue on with each of the other spark plugs making sure to always put the exact same wire onto the plug you took it off of. Note it is a good idea to put a small amount off anti-sieze compound on the threads of the new spark plugs to aid in the installation and removal. Also when reinstalling the spark plug wires use some silicone grease in the boot so that next time the boots will pull off easily. I hope this is some help. Melvis


What causes the spark plug wires to pop off a 1995 Honda delco vtec?

my plug wires pop off going down the road causing it to miss


What would cause an 02 Galant 2.4L to pop off spark plug wires?

if it keeps happening over and over, make sure the spark plug is screwed into the cylinder head completely; and make sure the electrode on the end of the wire is not open too far, just use a pair of needle nose pliers and clamp it just a little


Why does a starter on a 1991 Buick Century 3.3L disengage too soon and how do you fix it?

I had this problem with my 1990 century. Turns out ther silenoid on my starter was bad, I replaced it and it worked fine. Also when its dark outside pop the hood and have a buddy look for any spark at all when you try and start it. If you see one you may have a wet or lose wire, Dist. cap, or spark plug I had this problem with my 1990 century. Turns out ther silenoid on my starter was bad, I replaced it and it worked fine. Also when its dark outside pop the hood and have a buddy look for any spark at all when you try and start it. If you see one you may have a wet or lose wire, Dist. cap, or spark plug


What kind spark plug is recommended for Hyundai sonata v6 3.3?

Pop round to the local auto super mart. In the spark plug aisle you will find manufacturers catalogues for what plug in which vehicle and look yours up. Or ask the friendly assistant.


Why would the 4.3 pop through the throttle body?

Possible causes, mixed up spark plug wires, wet/damp spark plug wires, a bad distributor cap and/or rotor and a burned intake valve could cause the 4.3 to pop through the throttle body.