0
Why does the intake hose from the pool to the pump pinch closed?
Wiki User
∙ 13y ago
Its worn out replace it with another one or a heaver one
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Where is intake hose on pool?
The intake hose on a pool is typically used during cleaning. It is usually located inside the skimmer area. The drain at the bottom of the pool can also take in water.
On a pool filter what hose connects to the return?
On my filter, there are two connections arranged vertically. The top connection is the intake, the bottom the return.
Skimmer open or closed to vacuum pool?
If you have a dedicated suction for the vacuum hose (illegal in Australia) then you close the skimmer to increase suction.
What does it mean if you have a sputtering pool pump?
It may not be intaking enough water to fully make it work. Check your intake hose, it may be plugged.
How do you completely drain an above ground swimming pool when it has already been closed down and disconnected?
siphon the water out with a hose. You can even get a siphon going with a pool vac hose. Just get the whole hose full of water in the pool, keep one end of it submerged in the pool put yous hand over the other end so no air can get into it lift it over the edge of the pool and when it is below water level let go. the water will just pour out until there is no more water in the pool.
Is the Pool closed due to AIDS?
Yes. The pool is closed to due AIDS.
Is it illegal to swim in a pool that is closed?
yes it is illegal to swim in a swimming pool that is closed
What is the easiest and quickest way to siphon water from a wading pool with a garden hose without use of a pump?
If you have a low spot that you could put the end of a hose, than you could hook a hose to the other end and feed it water to get the flow started. After getting the water running, hold the connected ends under the water in the pool and take them apart. Keep the end from the hose going to the low spot under the water. Have something handy to put on the end in the pool to hold it down to the bottom. If there is no are leaks in the hose and you keep the end under water, it should mostly drain the pool.The discharge end of the hose must be lower than the intake end. When the level of water in the pool falls to the same level as the discharge end, the siphon will stop flowing. To drain a pool completely, the discharge end must be lower than the lowest spot in the pool and the intake end must be place at that spot. To start the siphon you can immerse the hose completely in water to get all the air out, plug the discharge end of the hose with your thumb or a suitable cap as you drag it over the side of the pool, and uncap it when the discharge end is at a low point. This method of starting a siphon avoids sucking or inhaling on the hose end, with the attendant risk of aspirating contaminated water into one's lungs.
How do you fill an indoor pool in?
with a hose
Pool filter looses vacuum when you attach vacuum hose?
submerge the hose in the pool first to get all of the air out, then attach to the skimmer.
What valves do you leave open when cleaning pool?
You should have two valves: one for the skimmers and another for the bottom drain. Close the valve to the bottom drain. One of your skimmers should have a rotating disc which will cover the intake at the bottom of the skimmer intake hole. Rotate the disc. In this manner all the suction from the pool pump will be at the one remaining skimmer. Attach your cleaning hose to this remaining skimmer while vacuuming the pool.
How do you drain your above ground pool with a garden hose?
Siphon it out. You can create a siphon by either sucking really hard on one end of the garden hose while the other end is under water, or the easier way, with 2 garden hoses as follows: -Get 2 garden hoses. Hook one to the spigot, put it in the pool and turn it on. set the other hose up with one end in the pool, and the other wherever you want to drain the water to. -Hold the ends of the 2 hoses that are in the pool, together with your hands, so the spigot water runs through the 2nd hose. Pull them apart, and you will feel the suction pulling the water out of your pool through the empty hose. -Take the hose that is connected to the spigot, out of your pool, and turn the spigot off. -Make sure the other garden hose does not fall out of the pool, or you will lose suction and have to start all over again! -When you get towards the bottom, you will have to physically hold the hose and move it around to get the water out without losing suction. You have to have the end of the hose that the water is running out of below the level of the bottom of the pool. You can do it with on.y one hose. Put one end of the hose in the pool and connect the other end to the faucet and turn it on until the air is forced from the hose. If the faucet is below the pool just disconnect the hose and lay it on the ground. You can move it around as long as the end of the hos estays below the top of the water. If the faucet is above the water level have someone put thier finger over the end of the hose in the pool while you move the end of the hose to a spot below the bottomof the pool.
