0
What else can I help you with?
Why does the intake hose from the pool to the pump pinch closed?
Its worn out replace it with another one or a heaver one
On a pool filter what hose connects to the return?
On my filter, there are two connections arranged vertically. The top connection is the intake, the bottom the return.
What does it mean if you have a sputtering pool pump?
It may not be intaking enough water to fully make it work. Check your intake hose, it may be plugged.
What hose type is used to transfer water to the pump intake from a pressurized source only?
hard intake hose
What is the easiest and quickest way to siphon water from a wading pool with a garden hose without use of a pump?
If you have a low spot that you could put the end of a hose, than you could hook a hose to the other end and feed it water to get the flow started. After getting the water running, hold the connected ends under the water in the pool and take them apart. Keep the end from the hose going to the low spot under the water. Have something handy to put on the end in the pool to hold it down to the bottom. If there is no are leaks in the hose and you keep the end under water, it should mostly drain the pool.The discharge end of the hose must be lower than the intake end. When the level of water in the pool falls to the same level as the discharge end, the siphon will stop flowing. To drain a pool completely, the discharge end must be lower than the lowest spot in the pool and the intake end must be place at that spot. To start the siphon you can immerse the hose completely in water to get all the air out, plug the discharge end of the hose with your thumb or a suitable cap as you drag it over the side of the pool, and uncap it when the discharge end is at a low point. This method of starting a siphon avoids sucking or inhaling on the hose end, with the attendant risk of aspirating contaminated water into one's lungs.
Where is the air intake temp sensor in a corolla 98?
The 1998 Toyota Corolla air intake temperature sensor can be found on the air intake hose. The air intake hose will come from the air intake box and proceed to the engine.
How do you fill an indoor pool in?
with a hose
Pool filter looses vacuum when you attach vacuum hose?
submerge the hose in the pool first to get all of the air out, then attach to the skimmer.
How do you change the water hose under the intake?
What's under the intake is not a hose, it's a pipe which a hose attaches to behind the intake manifold near the firewall. If the hose is leaking, it's a relatively easy task to replace it. If the pipe is leaking, you will have to remove the intake manifold which is not an easy task (minimum 6 hours to remove and replace the manifold!)
What is an PVC hose exactly?
a PVC hose is a hose connected to the back of the intake manifold to the front of the engine
Where is thermostat on 1994 silverado?
The thermostat is on top of your intake manifold, on the front side. Locate the radiator hose that runs to your intake, take the hose off and the thermostat will be sitting on the manifold under the hose.
How do you drain your above ground pool with a garden hose?
Siphon it out. You can create a siphon by either sucking really hard on one end of the garden hose while the other end is under water, or the easier way, with 2 garden hoses as follows: -Get 2 garden hoses. Hook one to the spigot, put it in the pool and turn it on. set the other hose up with one end in the pool, and the other wherever you want to drain the water to. -Hold the ends of the 2 hoses that are in the pool, together with your hands, so the spigot water runs through the 2nd hose. Pull them apart, and you will feel the suction pulling the water out of your pool through the empty hose. -Take the hose that is connected to the spigot, out of your pool, and turn the spigot off. -Make sure the other garden hose does not fall out of the pool, or you will lose suction and have to start all over again! -When you get towards the bottom, you will have to physically hold the hose and move it around to get the water out without losing suction. You have to have the end of the hose that the water is running out of below the level of the bottom of the pool. You can do it with on.y one hose. Put one end of the hose in the pool and connect the other end to the faucet and turn it on until the air is forced from the hose. If the faucet is below the pool just disconnect the hose and lay it on the ground. You can move it around as long as the end of the hos estays below the top of the water. If the faucet is above the water level have someone put thier finger over the end of the hose in the pool while you move the end of the hose to a spot below the bottomof the pool.
