Want this question answered?
The main disadvantage is that high voltage causes surrounding air ionization and may cause negative health effects for people close by. However, electric losses will be less when electricity is transmitted at high voltage. The higher the voltage the less the electric losses.
For a given load, the higher the supply voltage, the lower the resulting load current. So high voltages are essential for electricity transmission, in order to avoid enormous voltage drops, a need for conductors for huge cross-sectional areas, and to reduce line losses. Actual transmission sytem voltages are determined by the electricity-supply standards used in the country in which you live.
When looking at voltage numbers the higher the number the higher the voltage. In regards to which voltage is higher the 3.6v (volts) or the7.2v (volts), 7.2 is higher.
There is no particular benefit for having a higher open-circuit (or 'no-load') voltage. In fact, an ideal voltage source would have no internal resistance and, therefore, its open-circuit voltage would be identical to its closed-circuit voltage.
it all depends on the voltage the light bulb can sustain.
Electro motive force = EMF = Voltage.
The primary reason that power is transmitted at high voltages is to increase efficiency. ... The higher the voltage, the lower the current. The lower the current, the lower the resistance losses in the conductors. And when resistance losses are low, energy losses are low also.
The transformer provides the electricity at the right voltage for the house. In all countries it makes sense for all the houses to be fed with the same voltage, which simplifies the market for electrical applicances. Most countries use a standard voltage in the range 100-125 v or 220-240 v. The electrical energy has to be transmitted over long distances at a higher voltage unless you want to live next to a generator, so the transformer changes the voltage from a higher voltage like 6600 v to the correct voltage for the house, e.g. 230 v.
Electricity is transmitted to distant places through wires, held above the ground by pylons. The voltage is increased by transformers, before sending through overhead wires. This is done to reduce the effect of resistance in the wires. By ohms law, the loss of power from the resistance of the lines is less at higher voltage. The voltage is reduced by more transformers locally, before being sent to homes. Locally the powerlines may be buried underground. Alternating current (AC) was adopted as being best for power transmission. One reason is that the voltage of DC cannot be changed using transformers.
NO you pay by the kilowatt-hour
The main reason is that the voltage that the generator produces is not compatible with the residential and commercial voltages. The voltage generated could be in the range of 3.3, 6.6 and 11 kV. The consumer needs voltages in the range of 120/240, 120/208, 277/480 and 347/600. The second reason is that where the power is generated is usually miles from any urban areas where it is needed. From the generated voltage is it stepped up, with the use of transformers, to a much higher voltage in the range of 50 to 250 kV. The higher the transmitted voltage, the less voltage drop along the transmission lines. Once the voltage gets to the area that it will be used it is dropped back down, again with transformers, to the utility company's working voltage. This is the voltage that you use in residential, commercial and industrial applications.
The main disadvantage is that high voltage causes surrounding air ionization and may cause negative health effects for people close by. However, electric losses will be less when electricity is transmitted at high voltage. The higher the voltage the less the electric losses.
.10 amp could be fatel, the higher the ampage the more likely. Ampage is determined by the voltage and the resistance. ampage= voltage/ resistance
Because voltage is the power that makes electricity to circulate in a wire. Depending on the diameter, the lenght and material of the conductor (wire) the current, (the amount of electrons) flowing in the wire, the resistance will be lower or higher. Conclusively, the voltage is not the electricity itself, but it is like a pump that impulses the water through a pipe. Electricity is the current whose unit of measurement is the Ampere. So you have the voltage, resistance, and current in a electrical circuit on a direct current system.
Water molecules allows some electricity to constantly discharge. Only little humidity and the static electricity can grow to a quite high voltage. A lot of humidity will counteract this. As voltage increases, more will be dissipated by the moisture.
Tide = Flow of kinetic energy from higher ground to lower ground Wind = Flow of kinetic energy from higher pressure to lower pressure Electricity = Flow of electrical energy (transfer of kinetic energy) from higher voltage to ground or low voltage.
I would say, one type. But electricity comes in different varieties. For a start, there is DC and AC. Also, the electricity can come at a higher or lower voltage.I would say, one type. But electricity comes in different varieties. For a start, there is DC and AC. Also, the electricity can come at a higher or lower voltage.I would say, one type. But electricity comes in different varieties. For a start, there is DC and AC. Also, the electricity can come at a higher or lower voltage.I would say, one type. But electricity comes in different varieties. For a start, there is DC and AC. Also, the electricity can come at a higher or lower voltage.