answersLogoWhite

0

Compared to RIP, EIGRP has a lower administrative distance.

Compared to EIGRP, RIP has a higher metric value for the route.

Compared to RIP, the EIGRP route has fewer hops.

Compared to RIP, EIGRP has a faster update timer.

User Avatar

Wiki User

∙ 14y ago
User Avatar

What else can I help you with?

Related Questions

Which is a function of the show ip route command when used as a tool for troubleshooting network connectivity?

That's the command, on a Cisco Router, to show the routing table. It is one of the most important troubleshooting commands.That's the command, on a Cisco Router, to show the routing table. It is one of the most important troubleshooting commands.That's the command, on a Cisco Router, to show the routing table. It is one of the most important troubleshooting commands.That's the command, on a Cisco Router, to show the routing table. It is one of the most important troubleshooting commands.


Which three IOS troubleshooting commands can help to isolate problems with a static route?

To isolate problems with a static route in IOS, you can use the following commands: show ip route - This command displays the routing table, allowing you to verify if the static route is present and correctly configured. ping - This command tests connectivity to the next hop or destination address specified in the static route, helping to identify any reachability issues. traceroute - This command traces the path packets take to the destination, which can help identify where the traffic is being dropped or misrouted along the path.


What commands is used to ping a multi-function device?

The trace route command is used to ping a multi-function device.


What command is used to remove entries from the routing table?

The command used to remove entries from the routing table varies depending on the operating system. In Linux, the ip route del command is commonly used, for example: ip route del <destination>. On Windows, the command is route delete <destination>. Both commands require administrative privileges to execute successfully.


What commands allow you to view the routing table on your Linux workstation?

run the command: route -n You may need to be root (or use sudo) to run that command, or at least call its full path /sbin/route or /usr/sbin/route route --help will give you additional info, as will man route


How do you remove a static route from a routing table?

Assuming you have a Cisco router, you add a static route with the command ip route.... Therefore, you delete it with the command no ip route....Assuming you have a Cisco router, you add a static route with the command ip route.... Therefore, you delete it with the command no ip route....Assuming you have a Cisco router, you add a static route with the command ip route.... Therefore, you delete it with the command no ip route....Assuming you have a Cisco router, you add a static route with the command ip route.... Therefore, you delete it with the command no ip route....


Which of the following commands reveals the default gateway address for all the hosts to which a router is connected?

Using The ipconfig Command in Command Prompt.SyntaxC:\Users\\ipconfigMain syntax - ipconfigThe proper syntax is IPCONFIG /allThe slash-all shows everything.Do a IPCONFIG /? for all the commands used.ipconfig


Write difference in the form of a table between Ping and Trace Route command?

The Ping command sends a small packet of data to a destination IP address and waits for a response. It measures the time it takes for a packet to travel from the source to the destination. This command is typically used to check if a network device is online and responding to requests. On the other hand, the Trace Route command sends a series of packets to a destination IP address and tracks the route that each packet takes. It identifies each router or hop that a packet goes through on its way to the destination. This command can be used to diagnose network latency issues or identify where data is being lost. While the Ping command only provides information on the time it takes for a packet to reach the destination, the Trace Route command provides more detailed information on the network path and any delays or losses that occur along the way. In summary, both the Ping and Trace Route commands can be useful in troubleshooting network issues, but they serve different purposes. The Ping command is a simple tool for testing connectivity to a destination device, while the Trace Route command provides more detailed information on the network path and any issues that may be occurring.


What commands can be used to view a host routing table?

netstat -r and route print


What command is used to view a PC computer's routing table?

your command would be show ip route or sh ip route static


How can you see the kernel routing table?

You can view the kernel routing table in Linux by using the command route -n or ip route show. These commands display the current routing table, showing destination networks, gateways, and the interface used for routing packets. Additionally, you can use netstat -r to achieve similar results.


Which are the networking commands in unix?

It depends on which networking protocol you are asking about. For TCP/IP, some of the common commands are: ping netstat ifconfig route traceroute