0
The limiting shear failure method is not commonly used today because it is considered overly conservative and may result in unnecessary reinforcement. More accurate and advanced analytical methods like the strut-and-tie model and finite element analysis are typically preferred for assessing shear resistance in concrete structures. These methods provide a better understanding of the structural behavior and allow for more efficient design solutions.
Add your answer:
Earn +20 pts
What are the different types of slope failure for rock slopes?
1. shear failure 2. rock flow 3. rock fall
Advantages and disadvantages of the shear box test?
Advantages: 1) The test's simplicity and, in the case of sands, the ease of specimen preparation. 2) The travel of the machine can be reversed to determine the residual shear strength values, which is shear strength parameters at large displacements. 3) Shear box represents a cheaper method in determining the drained shear strength parameters for coarse-grained soil. Preparing soil samples for other testing methods is relatively difficult and expensive. disadvantages: 1) The main one: drainage conditions cannot be controlled. 2) As pore water pressure cannot be measured, only the total normal stress can be determined, although this is equal to the effective normal stress if the pore water pressure is zero. 3) Only an approximation to the state of pure shear is produced in the specimen and shear stress on the failure plane is not uniform, failure occurring progressively from the edges towards the center of the specimen. 4) The area under the shear and vertical loads does not remain constant throughout the test.
How does the shear box tests where water is used as a pore water fluid. Discuss how the different drainage conditions for various soil types(sand silt and clay) may affect the measurement of the?
shear stress at failure?
Why is compacting a landfill so critical?
Two reasons: to save space and to strengthen it (to limit settlement and to prevent shear failure).
What does ASME Section V Article 3 referenced to?
Secret NDT Method which ASME don't want to shear
Differences between triaxial test and shear box test?
Shear box tests are generally suitable for cohensionless soil except fine sand and silt whereas triaxial test is suitable for all types of soils. Pressure changes and volume changes can be measured directly in triaxial test which is not possible in shear box test. Pore water pressure can be measured in the case of triaxial test which is not possible in direct shear test. Triaxial machine is more adaptable. The stress distribution across the soil sample in the failure plane is more uniform in triaxial test. The complete state of stress is known at all intermediate stages up to failure during the triaxial test whereas only the stress at failure are known in the direct shear test. In triaxial test, there is complete control over the drainage conditions, where control of drainage conditions is very difficult in shear box test.
Why shaft diameters are not calculated using relation shear stress by radius equals g x theta by L and what is the significance of the radius so found?
If you know the allowable shear strength and the shaft is only in torsion, your equation is correct - the radius is the maximum you can have before failure, knowing the shear strength. Diameter is two times radius
How tension crack causes slope failure?
Thension crack is generated by the difference in shear movement along the failure surface or slip plane. It formed in the upper slope face before the major failure surface appeared. So, the total shear resistance and thus the safety factor will reduce after this tension crack developement. However, this tension crack will stop developing when it reaches a critical depth. And, a new tension crack will develope behind that previous crack.
What has the author Richard S Bray written?
Richard S Bray has written: 'A method for three-dimensional modeling of wind-shear environments for flight simulator applications' -- subject(s): Vertical wind shear, Flight simulators
Relationship between the shear stress and angle of shear?
Shear Stress divided by the Angle of Shear is equals to Shear Stress divided by Shear Strain which is also equals to a constant value known as the Shear Modulus. Shear Modulus is determined by the material of the object.
What is negative shear and Positive shear?
The difference between a positive shear and a negative shear is the direction the image is distorted into
Is it safe to drive on bad wheel bearings?
No, no and did I mention NO(?)!Worst case failure is the wheel comes off.You want to risk it?...Get 'em checked, get 'em replaced.No, wheel could seize, spindle could shear off No, wheel could seize, spindle could shear off
