0
Why must the specimen be centered before switching to high power on a microscope?
Wiki User
∙ 9y ago
I don’t know
Anonymous
Add your answer:
Earn +20 pts
Why should the specimen being viewed through the microscope be centered in the field of view before you increase the magnification?
as you zoom in the view gets bigger and if its not in the middle you wont be able to see it properly .
Why the specimen be centered in field of view on low power before going to high power?
Because it is too hard to find a specimen on high power. Easier to find them and focus them on low power and then increase the magnification and fine-tune the focus to get a better, closer look.
What are three ways to keep the microscope from getting damaged?
Always carry a microscope with two hands. Place one hand under the base of the microscope and hold the arm with the other hand. Do not allow the microscope to drop or bump into anything while carrying it. This could damage the microscope or cause small pieces to break off that could cause a tripping hazard. Touching the microscope lens can smudge or damage it. Always use lens paper or a soft cloth with a small amount of isopropyl alcohol to clean a dirty microscope lens. Remove slides and cover slips from the stage before storing the microscope, and rotate the nose piece so that the smallest power objective is facing the stage. Place a dust cover over the microscope when storing it to prevent dust and dirt from damaging the machine. Read more about Microscope Saftey Procedures in the related link.
Why should you watch from the slide before you lower the objective of your microscope?
Movements viewed through the microscope are exaggerated quite a bit. As such, it's best to attempt to line up the object on the slide by looking at the slide directly, rather than through the objective.
When you use a microscope why do you have to put the smallest lens back into place before putting the microscope away?
Because otherwise the sample might hit one of the lenses during loading or unloading. The smallest objective lens is always further away from your sample, that makes it safer to (un)load.
Why is it important that the object is centered in the field of view before switching to a higher power objective?
WHY IS IT IMPORTANT THAT THE IMAGE IS CENTERED IN THE FIELD OF VIEW BEFORE SWITCHING TO A HIGHER POWER
Why should the specimen being viewed through the microscope be centered in the field of view before you increase the magnification?
as you zoom in the view gets bigger and if its not in the middle you wont be able to see it properly .
What is a Specimen Smaller Than 0.2 Micrometers Must Be Completely Dried Out Before Being Studied Using This Type Of Microscope?
Electron Microscope
What two things must be true before the microscope can be switched to high power to zoom in on a specimen?
its what is in the poo
Microscope image centered and viewed on low first before high?
lower= further away than high
Why must the specimen be centered before switching from low power to high power?
Because high power takes up a much smaller area, and you may not be able to find the specimen if it's off to one side. C:
What does low power objective do?
The low power objective lens is usually a 10x lens and it is used to orient the specimen and get it focused before switching to a higher power lens.
What does low power objective len do?
The low power objective lens is usually a 10x lens and it is used to orient the specimen and get it focused before switching to a higher power lens.
What is an Abbe condenser?
An Abbe condenser is a condenser composed of two lenses which concentrates and controls the light which passes through a specimen before the light enters the objective of a microscope.
What is Abbe condenser?
An Abbe condenser is a condenser composed of two lenses which concentrates and controls the light which passes through a specimen before the light enters the objective of a microscope.
The specimen must be centered in the field of view on low power before going to high power?
Because when looking at it from far, then you can see more of the specimen, However, when you're looking at it closer up in a high power mode, then you will see less of the object, but much closer.
Why the specimen be centered in field of view on low power before going to high power?
Because it is too hard to find a specimen on high power. Easier to find them and focus them on low power and then increase the magnification and fine-tune the focus to get a better, closer look.
