0
Following a power cut, it's important that motors aren't allowed to self-start when the power is restored, as that would represent a serious hazard. So, a no-volt coil is a part of a motor-control system that ensures, in the event of a power cut, the control system disconnects the motor so that it cannot self start.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is no volt coil?
no volt coils are used to de-energise a contactor should a situation arise in which voltage is zero
Do you replace the coil from a 6 volt to a 12 volt when converting from 6 volt to a 12 volt system?
Yes. Since the coil is run at full voltage when starting 12 volts may be too much for a 6 volt ignition coil. It would be at about 8 volts when running. There is a starting resistor.
How do you rewire a 110 volt HID Magnetic coil ballast to use 220 volt?
Unless the ballast is a multi tap primary you can not rewire it for 220 volts.
How do you use 12 volt battery on 6volt coil?
Use a rheostat to lower the voltage to six volts
How do you control 110 volt circulator pump with a 24 volt thermostat?
You will need an interpose relay. This relay will have a 24 volt coil. The circuit power for the relay will come from a 120VAC to 24VAC volt transformer. The 24 VAC circuit will have the thermostat in series with the coil of the relay. Thermostat calls for heat, the coil energizes and the relay's contacts close. Your circulator pump is controlled by the relay. On selecting the relay make sure that the contact ratings can handle the full load amps of the circulator. A contact rating of 120 volts at 15 amps will do very nicely.
What is no volt coil?
no volt coils are used to de-energise a contactor should a situation arise in which voltage is zero
What happens if you use a 12 volt coil with a 6 volt system?
Probably not much because 6 Volts is not enough to power a 12 Volt coil
Do you replace the coil from a 6 volt to a 12 volt when converting from 6 volt to a 12 volt system?
Yes. Since the coil is run at full voltage when starting 12 volts may be too much for a 6 volt ignition coil. It would be at about 8 volts when running. There is a starting resistor.
What is the number of turns in primary and secondary coil for 12 volt battery charger with 220 volt power supply?
what is the number of turns in the primary and secondary coil for 12 volt battery charger with 220 volt power supply> what is the number of turns in the primary and secondary coil for 12 volt battery charger with 220 volt power supply>
Why not no volt coil?
It is impossible to figure out the question.
What would be the result if a 24 volt 20-ohm low voltage contactor coil were wired in series with a 24 volt 200-ohm control relay coil?
Nine tenths of the voltage would appear across the 200-ohm coil.
Can you use a 6 volt relay to 230 volt circuit?
If you are talking about a 6 volt coil, yes, so long as the contacts are rated for the 230 volt circuit. If you are talking about 6 volt contacts, no, absolutely not.
Can a coil be made to fire not being on a car?
probably an old style 6 volt coil with an old-style 'lantern=battery' (6 volt) big fat square thing with the springs on top or old style 12 volt coil with like gas lawn mower key-start (completely sealed) battery /has male tabs/ on top. but coil will not hold a charge for later use.
When making a secondary coil for a Tesla coil is it ok to take two long copper wires and solder them together then coil it?
In the related links box below, I posted Building A 250,000 Volt Tesla Coil.
How is coil a transfer of energy?
Coil is a transfer of energy because it takes energy to make coil burn which is reduced as heat/ light energyMy VersionA electrical coil will step up (convert) voltage and electrical energy or step down depending on how it is designed. EG: A coil called a transformer will take the 600 volt power from the power grid and turn it into 120 volt power in your house.
What voltage is the hot wire to the coil on a 1985 s10 blazer 2.8?
12 volt.
How do you rewire a 110 volt HID Magnetic coil ballast to use 220 volt?
Unless the ballast is a multi tap primary you can not rewire it for 220 volts.
