0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many suspenssion type insulation used in 66kv transmission line?
one insulator unit can bare 11kV. such that 66kV tx line needs 6 insulator units.
What is maximum transmission voltage in Pakistan?
It is 500kv between rahim yar khan and multan.
Where can use voltage of 415v 11kv 66kv 33kv and 132kv?
These are the nominal voltages used by the UK's distribution system, although (to comply with European Harmonisation requirements, 415 V has now been 'replaced' with 400 V. Incidentally, the symbol for the volt is a capital 'V', not a lower-case 'v'.
How many volts in three phase?
Three phase refers to have the power over three lines one delayed by one third of the electrical cycle and the other by two thirds. (The first line is not delayed) Three number of phases has no relationship to the voltage (or frequency for that matter). Power can be delivered by three phase in any voltage whatsoever and there is no reason why the power could not be 1 volt (OK, not really practical) or could be over 660,000 volts and this is very common. Often voltages are 415, 3,300 (3.3kv), 6,600(6.6kv), 66kv and 132kv but these are just examples from my experience. Power voltage throughout the world varies enormously and so it is impossible to stipulate a voltage.
What is diff between vcb and sf6?
SF6 (Sulfur Hexaflouride) is the god of gaseous dielectrics. It is a VERY poor conductor, and when it does decompose in an arc, it re-assembles itself in short order. It is also dense, so that it sinks to the floor, and pools in the lowest spot it can get to. This also makes it great in breaking arcs, because it makes it highly thermally conductive, stealing the heat from the arc & diffusing it. SF6 breakers are generally smaller than other types (of the same handling capacity), and therefore lighter. There's nothing we've found better with high voltage. Vacuum is decent. It has fair dielectric strength, can break an arc pretty well. It has one massive advantage over SF6: It is environmentally benign. SF6 is pretty destructive, and has a 3200 year life in the atmosphere. That's tenacity ! So, it has been suggested that if your application is below 36kv or so, you should stick with the VCBs, but you can't beat the handling of SF6 as you go higher.
Why is the rating of transformer is like 11kv 33kv 66kv?
Because the tranformer calculation for ratings is calculated with the formfactor which is 1.11 constant. Regards Mithin kudva
How many suspenssion type insulation used in 66kv transmission line?
one insulator unit can bare 11kV. such that 66kV tx line needs 6 insulator units.
What is maximum transmission voltage in Pakistan?
It is 500kv between rahim yar khan and multan.
What is the voltage coming out of a station?
Depends on the sub station. It could be 11KV, 33KV, 66KV,110KV, 220KV, 400 KV etc
What is the voltage of high tension electrical transmissions towers?
Usually HV is 33KV and 66KV, EHV is 132KV, 220KV and 400KV and UHV is 800KV and 1200KV
What is the Phase to phase voltage of 66KV earthed cable?
Nominal transmission and distribution voltages are line voltages. So '66 kV' is a line-to-line voltage. Note that there is no such thing as a 'phase-to-phase' voltage -the correct term is 'line-to-line'. Using the term, 'phase-to-phase', indicates a lack of understanding of a.c., which is not uncommon! Incidentally, the symbol is 'kV', not 'KV'.
What is Procedure the procedure to select CT's and PT's in 66kV and above substation?
You need to required following data Voltage Level, Current, Protection Class, SC Current
What is the minimum height for high power lines over a road?
On 11-66kV not less than 5,5 metres,with hazard signs on both sides indicating height of line.
What is difference between lt and ht pannel?
lt pannel is a iow tensan pannel. lt pannel work is 240v and 440v. ht pannel is a high tensan pannel . ht pannel work is 11kv,33 kv ,66kv, 120kv
Where can use voltage of 415v 11kv 66kv 33kv and 132kv?
These are the nominal voltages used by the UK's distribution system, although (to comply with European Harmonisation requirements, 415 V has now been 'replaced' with 400 V. Incidentally, the symbol for the volt is a capital 'V', not a lower-case 'v'.
Why the generating transformers are in 66kv?
As we all know that at the generating station if the the voltage ratings are at higher level like 66 KVto 132 KVso due to it we can obtain a good transmission line with a lower voltage drop and also the voltage ratings can be decreased with the help of step up or step down transformer upto10% very easily at the receiving station.Thanks & RegardsMithinKudva
What voltage does New Zealand use?
New Zealand uses 230 V @ 50 Hz, the same as the UK and Australia. Wall power outlets are the same as Australia - two flat live and neutral blades in an inverted-V shape, with a single vertical flat earth pin below New Zealand's mains supply is incompatible with appliances designed for the US and Canada (120 V @ 60 Hz) - so do not attempt to put a US appliance in a NZ socket by bending the pins. High voltage lines are usually at 230/400 V, 6.6kV, 11kV, 22kV (local distribution), 33kV, 50kV, 66kV (sub-transmission), 110kV, 220kV (transmission) and +/-350kV HVDC (the inter-island link connecting the North and South Islands across Cook Strait)
