0
Why superdisintegrant is added to the internal phase of wet granulation?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can you connect a 3 phase motor to a 1 phase supply?
Single phase to three phaseThe physical internal windings between single phase and three phase motors makes this an impossibility That being said money can make anything happen. Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase motor. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input terminals and the unit will not start.Some 3 phase motor speed controllers can be run off a single phase supply, this caused us a problem at work when a new speed control was fitted to some laundry equipment, as we then had to rewire the supply to bring in a nuetral, so i suggest a speed controller is probably the solution.
Why do you have voltage to ground but not voltage phase to phase?
There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!
What are the three types of phase on its final phase?
single phase, double phase & three phase
What is 11 kV single phase?
for USA, Canada and other countries running a 60 Hz supply service.A 11kV single phase line is one phase of a three phase system. The three phase system voltage is found by multiplying 11kV x 1.73. The three phase primary system voltage is 19kV. A transformer with a 11 kV primary can have a secondary of 115/230 depending on the internal connections in the transformer's case.For the UK11 kV is the standard three-phase h.v. distribution voltage in the UK, where it is a line voltage (i.e. it is the voltage measured between any pair of the three line conductors). A single-phase distribution transformer is connected between any two lines, so 'single-phase 11-kV' is simply a connection made between any two lines of an 11-kV three-phase system.As the primary windings of three-phase 11-kV distribution transformers are delta (3-wire) connected, the primary phase voltage is numerically equal to the primary line voltage (11 kV).
Is there continuity between a three pole circuit breaker terminals?
No, the three individual poles of a three phase circuit breaker are not electrically connected to each other. If they were, a fault would develop internal to the breaker.
During the phase of tissue repair capillary buds invade the clot forming a delicate pink tissue?
Granulation tissue
As heat is added to a substance undergoing a phase change. why does the temperature remain?
Basically what it comes down to is the substance that is left behind during the phase change (say the liquid when it is changing to a vapor) has a lower internal energy than it had before the phase change started. To maintain the substance at its original temperature, an equivalent amount of energy must be added to make up for the loss of internal energy due to the phase change. (Conservation of Energy)The energy added in this case is heat, which in turn causes more molecules of the substance to change phases and lowers the internal energy & the process repeats. This is why the temperature remains constant as you add heat to a substance during a phase change. Once the phase change is completed the added heat will eventually cause the temperature to rise in the new phase of the substance. Hope this explanation helps. It's kind of hard to explain without a basic knowledge of thermodynamics.
During the first phase of tissue repair capillary buds invade the clot forming a delicate pink tissue called?
Granulation Tissue
What happens to the energy added during a phase change?
The added energy is used in the phase change to break intermolecular bonds.It is used for the phase change. ~ APEX
What happens to energy added during a phase change?
The added energy is used in the phase change to break intermolecular bonds.It is used for the phase change. ~ APEX
What has to be added to a substance to cause a phase change?
Heat energy must be added to or subtracted from a substance to cause a phase change.
What happens to the energy added during the phase change?
When energy is added during a phase change the energy is used to break molecular bonds.
What is the third step in the internal coordination phase?
Identify Respondents
State in which biological rhythms are not in phase with one another?
Internal desynchronization A state when biological rhythms are not in phase with each other
Why does the temp of water not increase during a phase change?
These are phase changes - All the energy that is added at this time is used to change the phase of the substance.
Which is an internal regulator of the cell cycle?
in the mitotic phase, it makes sure that everything is in order and that nothing will go wrong before it goes on to the next phase.
What is Internal desynchronization?
is a condition in which our body's biological rhythm are not in sync, or not in phase with one another.
