answersLogoWhite

0

Superdisintegrants are added to the internal phase of wet granulation to enhance the disintegration of the granules upon contact with liquid in the gastrointestinal tract. They facilitate rapid breakdown of the granules into smaller particles, promoting faster dissolution and absorption of the active pharmaceutical ingredient. This improves the overall bioavailability of the drug and ensures more consistent therapeutic effects. Additionally, superdisintegrants can help maintain the integrity of the granules during the manufacturing process while still enabling quick disintegration in the final dosage form.

User Avatar

AnswerBot

3w ago

What else can I help you with?

Continue Learning about Engineering

Why internal phase in emulsions is called discontious phase?

The internal phase in emulsions is referred to as the discontinuous phase because it exists as small droplets dispersed throughout the continuous phase. This phase is not uniformly distributed and is often separated from the continuous phase by a distinct interface. The discontinuous nature of the internal phase is crucial for the stability and functionality of emulsions, allowing for the unique properties that emulsions exhibit, such as texture and stability.


How do you wire a 36 volt 3 three phase forklift charger up to run on single phase power?

To wire a 36-volt three-phase forklift charger to run on single-phase power, you first need to ensure that the charger is compatible with single-phase input voltage. Connect two of the three phases together and use them as the input for the charger, while leaving the third phase unconnected. Additionally, you may need to adjust internal jumpers or settings on the charger to accommodate the single-phase input, and ensure proper fusing and circuit protection is in place. Always refer to the manufacturer's specifications and guidelines for safety and compliance.


Can you connect a 3 phase motor to a 1 phase supply?

Single phase to three phaseThe physical internal windings between single phase and three phase motors makes this an impossibility That being said money can make anything happen. Depending on the amount of money you want to spend to make this happen there is a device on the market called a VFD ( Variable Frequency Drive). On the three phase input terminals you apply your single phase voltage. On the output terminals you connect your three phase motor. When run in this configuration there is an internal switch that has to be changed to let the VFD know that it should be looking for only two lines on the input to be hot. Other wise the VFD thinks that there is a line loss on the three phase input terminals and the unit will not start.Some 3 phase motor speed controllers can be run off a single phase supply, this caused us a problem at work when a new speed control was fitted to some laundry equipment, as we then had to rewire the supply to bring in a nuetral, so i suggest a speed controller is probably the solution.


Why do you have voltage to ground but not voltage phase to phase?

There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!


What are the three types of phase on its final phase?

single phase, double phase & three phase

Related Questions

During the phase of tissue repair capillary buds invade the clot forming a delicate pink tissue?

Granulation tissue


When does the internal energy increases?

The internal energy of a system increases when energy is added to the system through heat transfer or work done on the system. This can result in an increase in temperature, change in phase, or other forms of internal energy change.


During the first phase of tissue repair capillary buds invade the clot forming a delicate pink tissue called?

Granulation Tissue


What tissue is formed during the first phase of tissue repair?

During the first phase of tissue repair, the tissue that is formed is known as granulation tissue. This tissue is composed mainly of new blood vessels, fibroblasts, and extracellular matrix components such as collagen. Granulation tissue helps to fill the wound site and support further tissue repair and regeneration.


What happens when heat is added to a system?

When heat is added to a system, the temperature increases, unless there is a phase change taking place. In that case, temperature remains the same, and the only observable difference is the phase change.


As heat is added to a substance undergoing a phase change. why does the temperature remain?

Basically what it comes down to is the substance that is left behind during the phase change (say the liquid when it is changing to a vapor) has a lower internal energy than it had before the phase change started. To maintain the substance at its original temperature, an equivalent amount of energy must be added to make up for the loss of internal energy due to the phase change. (Conservation of Energy)The energy added in this case is heat, which in turn causes more molecules of the substance to change phases and lowers the internal energy & the process repeats. This is why the temperature remains constant as you add heat to a substance during a phase change. Once the phase change is completed the added heat will eventually cause the temperature to rise in the new phase of the substance. Hope this explanation helps. It's kind of hard to explain without a basic knowledge of thermodynamics.


Why internal phase in emulsions is called discontious phase?

The internal phase in emulsions is referred to as the discontinuous phase because it exists as small droplets dispersed throughout the continuous phase. This phase is not uniformly distributed and is often separated from the continuous phase by a distinct interface. The discontinuous nature of the internal phase is crucial for the stability and functionality of emulsions, allowing for the unique properties that emulsions exhibit, such as texture and stability.


What happens to the energy added during the phase change?

When energy is added during a phase change the energy is used to break molecular bonds.


What is the third step in the internal coordination phase?

Identify Respondents


What happens to the energy added during a phase change?

The added energy is used in the phase change to break intermolecular bonds.It is used for the phase change. ~ APEX


What is the step in the internal coordination phase that allows you to coordinate the action from office to office?

Send it out


Which is an internal regulator of the cell cycle?

in the mitotic phase, it makes sure that everything is in order and that nothing will go wrong before it goes on to the next phase.