0
The agitator has two parts. One is the bottom agitator and then you have the top agitator that moves the clothes around. If the top part of the agitator is not moving. You probably need to replace the dog ears. A great sight to look this info up is www.repairclinic.com. I have ordered from them before. Good Luck! Karen
What else can I help you with?
What is the difference between an agitator and an impeller in a washing machine?
Top-loaders have two options for swirling the load: an agitator (central spindle), or an impeller (a small bump at the bottom of the bowl). Impellers spin and pulse to turn the washing over, rather than twisting it. Washing machines with impellers tend to be easier to load and unload, but their dirt removal isn't always as good as agitator models.
How do I turn off the water supply to the washing machine?
To turn off the water supply to the washing machine, locate the shut-off valves behind the machine and turn them clockwise until they are fully closed. This will stop the flow of water to the washing machine.
How do I turn off the water to the washing machine?
To turn off the water to the washing machine, locate the water supply valves behind the machine and turn them clockwise until they are fully closed.
How can I turn off the water to the washing machine?
To turn off the water to the washing machine, locate the shut-off valves behind the machine. Turn the valves clockwise to close them and stop the water flow.
What energy transformation that occur in washing machine?
Electricity is transformed into mechanical energy to turn the motor, which then moves the agitator or drum to clean the clothes. Some energy is also converted into heat to warm the water during the wash cycle.
How do you turn on a washing machine?
To turn on a washing machine, first plug it into a power outlet. Then, select the desired wash cycle and water temperature. Finally, press the start button to begin the washing cycle.
How do you stop water from gushing out the powder tray of the washing machine?
just put a bucket under the door of your washing machine! Call a plumber and turn the washing machine off in the mean time.
How does the agitator work on a washing machine?
the agitator on most washers go back and forth . at least one i know of goes up and down. we will talk about the back and forth.Underneath the tub usually accessable from the back of the machineis a transmission and belt along with other things. when you start the washer it will fill with water . When the correct volume of water is reached a switch is activated that sends power to the timer which in turn routes power to the proper connections needed to agitate. now when washing power is sent to a agitator control which lifts a plunger that makes the transmission rock back and forth which is calledagitation
How can I stop a washing machine from running?
To stop a washing machine from running, you can press the "Pause" or "Stop" button on the machine's control panel. If there is no specific button, you can unplug the machine from the power source or turn off the circuit breaker that supplies power to the machine.
How do you stop delay end for samsung washing machine?
Just simply turn the washer off, then turn it on again.. :)
How do you get a lost ring out of a washing machine?
I dropped engagement ring in washer and it slid under the agitator .. out of panic, I drained the water and let it go through the spin cycle hoping it would shake it out but it didn't.. so i checked if my machine has a filter, its usually located on the bottom corner of machine.. if not in the filter or like my machine it didnt have a filter then this is what i did.. first do not let it go through another wash cycle.. second turn the main source of water off that supplies water to the washer.. third, unhook the hose connected to washing machine (be prepared for lots of excess water draining out).. step four, turn machine on wash cycle and if ur lucky like I was then the ring will pop right out the drain : )
How can I fix the breaker for my washing machine?
If your washing machine trips its breaker, first reset it. If it trips again, the issue is likely with the machine. Common causes include an overloaded circuit, a faulty heating element, motor, drain pump, or damaged wiring within the washer. For persistent issues or if you're uncomfortable dealing with electrical components, it's safest to consult a qualified electrician or appliance repair professional.
