answersLogoWhite

0

Yes, the larger cable can carry more load (current) than the other cable.

User Avatar

Kennith Lockman

Lvl 10
3y ago

What else can I help you with?

Related Questions

Will a 12v 2 amp device work with 12v 5 amp power cable?

Yes, the larger cable can carry more load (current) than the other cable.


Will a 12v 1.5 amp device work with 12v 2.5 amp replacement power supply?

No. The amperage describes the total electrical energyeither produced or consumed. Voltage just describes the potential. If the power cable or power supply are only capable of 1 amp and the device consumes 2 amps... sorry, you don't have enough electrical energy available.


Will a 12v 2 amp device work with 12v 2.5 amp power cable?

Providing that you maintain the same voltage and above all, make sure that the polarities are the same, yes, it should work. It's OK to have a little more power available than the device requires but it shouldn't be less, which can cause the cable to over heat or cause undue stress on the device itself. It sounds as though you're using a wall adapter to run something, and the extra .5 amp capacity should be OK. But, when using a wall adapter, always try to keep as close to the rating of the device as possible. Wall adapters that provide more power than what's needed, can over heat because the extra power isn't being used. It's just being converted to heat. Since you're within 20 percent of the device's ratings, this shouldn't be a problem.


Is an amp a speaker?

No, an amp (amplifier) is not a speaker. An amp is a device that increases the power of an audio signal, while a speaker is a device that converts electrical signals into sound waves.


Could a 240 watt max amp work using a 1800 watt power cable?

no you must go lower or the same


How do you install a car audio capacitor?

power cable goes from battery to cap + terminal. separate power cable from cap + terminal to the amp. make sure the amp and cap are grounded.


Can you use 1 amp power supply for 1.5 amp device?

The simple answer is, No. But I'll give you the long answer, too. The power rating of most devices is the maximum power used under unusual circumstances. Most devices, unless it's something like a light bulb which is either on or off, don't use their max power 99% of the time. If you protect the circuit with a 1.0 amp fuse you protect your power supply and device and you can safely see if it works.


Where do you hook up remote wire when using stock CD player?

the remote wire only needs a power source for the amp to turn on, so if u have a looped cable running from the remote input on the amp to the front of the car with a switch and then back to the power cable on the amp u can control when the amp is on just by turning the switch on or off. otherwise u will have to figure out which cable on the back of the stereo is switched power, or which cable only supplies power when the car is running. and that would require a wiring diagram.


What will be the effects of using a 12V 1.5A power source to a 15V 1A device?

Most likely, yes. If your device requires 12 volt and draws 1 Amp of current, a 12 volt power supply will give the required voltage and will be able to supply the 1 amp of current it needs to run. A power supply that supplies a little more voltage might also work but depending on the device may cause the device to fail sooner. Much more than 12 volts will most likely destroy the device and result in a burning smell and smoke. A power supply for less than 12 volts may fail to power the device or may make it run slower. This would be like using a battery in a device and as the battery gets weaker, it supplies less voltage and the device slows down or a flashlight get dimmer till it stops working. A 1.5 amp power source is capable of delivering 1.5 amp of current to the device. If the device need less (only 1 amp), it still gets the amount it needs to function. If the power supply was rated at 10 A or 100 A, the device will still only use 1 A to function. If the power supply were rated at less than 1 amp. The device might not get enough current to run.


What size power cable do I need with a Crunch Power Zone P18004 amp?

This unit requires a PWM power supply.


What do AMP connectors do?

AMP connectors are used for power cords and sockets. They will help your power cord work.


Can you replace a 7 amp 125 volt power cord with a 3 amp 125 volt power cord?

If the device you are powering requires 7 amps of power, then no. You will need to find a replacement cord with 7 amps. Check the power input requirements of the device to find out.