0
Will a double pole switch work where only a single pole is needed?
Wiki User
∙ 15y ago
Yes, make sure you wire it correctly. Some switches connect across the screws and some connect like a conventional switch where the screws are below one another.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the difference between iron clad double pole switch and double pole single throw switch?
Answer for USA, Canada and countries running a 60 Hz supply service.The difference between a double pole switch and a single pole switch is the use of the switch in the installation or equipment. A double pole switch is used when the voltage from two circuits has to be broken. An example of this is a 240 volt supply. A single pole switch is used where there is only a single supply voltage that has to be broken.
What is the difference between single pole double throw switch and single pole single throw switch?
US Single-pole switchIn the US, the standard "single-pole" light switch is single-pole single-throw, with only 2 terminals. In the ON position it connects the two terminals, and in the OFF position it doesn't. The standard US "3-way" light switch (used for switching a light from two different switches) is single-pole double-throw. It has 3 terminals (hence the term "3-way"), and it connects one of those terminals to either of the other two, depending on the switch position. There's no OFF position, so the switch has only two positions.
Why sepic called single ended converter?
Single ended is referred to converters with single switch topology. SEPIC has only one switch and hence named Single ended primary inductor converter. (Primary inductor because the inductor is charged during ON cycle of the switch) For example, There are double ended flyback topologies with two switches. It is named as double ended because it contains two switches.
What is difference between single pole and double pole switch?
A single pole switch interrupts only one wire, which must be the live wire. A double pole switch interrupts both the live and the neutral, so it contains two separate switches operated by the same lever. Current practice is to use single-pole switches, to avoid a fault condition which could leave equipment live while switched off.
The average bond enthalpy for a double bond is 614 and that of a single bond is 348 Estimate the energy needed to break only the bond of the double bond of 2-butene?
264000
How does a single pole switch differ from a three way?
A proper "3-way switch" would be capable of being switched to 3 different positions and could have one, two or more poles. Each pole could be either single- or double-throw."How does a single pole switch differ from a three way?" is a trick question often asked to catch-out new trainee electricians because the common but mis-named "three-way switch" is actually a single pole, double throw switch, i.e. it is only a 2-way switch, not a 3-way switch.A pair of "3-terminal, single pole, double throw" switches are often used to hook-up two separate light switches to control one light or one set of lights.The same answer put in a different wayDespite the fact that the name "3-way switch" is often used to describe it, if it is of the type that has just one pole that can only be physically switched 2 ways, the name "3-way switch" is quite wrong for that particular switch. A "3-terminal, single pole, double throw" switch" is a more accurate description for it.
Ch4 have single or double bond?
CH4 has only single bonds.There are no double bonds.
What is dpst switch?
Double pole Single Throw switches are sometimes called DPST switches. Assuming the circuit is single phase two wire system, DPST - are used to isolate the ciruit. Isoloation occurs on both terminals hence it is called double pole. This isolation occurs at only one end in the circuit, hence it is called single throw.
How did a 'three-way switch' get its name?
"How does a single pole switch differ from a three way?" is a trick question often asked to catch-out new trainee electricians because the common but mis-named "three-way switch" is actually a single pole, double throw switch, i.e. it is only a 2-way switch, not a 3-way switch.A pair of "3-terminal, single pole, double throw" switches are often used to hook-up two separate light switches to control one light or one set of lights.A proper "3-way switch" would be capable of being switched to 3 different positions and could have one, two or more poles. Each pole could be either single- or double-throw.The same answer put in a different wayDespite the fact that the name "3-way switch" is often used to describe it, if it is of the type that has just one pole that can only be physically switched 2 ways, the name "3-way switch" is quite wrong for that particular switch. A "3-terminal, single pole, double throw" switch" is a more accurate description for it.Comment'Three-way switch' -American term. 'Two-way switch' -UK term for the same type of switch. Used to operate a lamp from two different locations.
Does SO3 only have single bonds?
No there are no single bonds.There are double bonds.
Can a three way switch be changed to a single pole switch with a plate over one of the switch locations?
Yes, If you only hook up two wire it will work as a single pole
How many current sensing devices are required by the National Electrical Code to protect a single-phase motor operated on 240 volts?
For a single phase fractional horsepower motor, only one over current device is needed in the motor feeder. This protection can come in the form of a switch which has the overload heater incorporated into it. These switches come in single and double pole configurations. Select the heater for the motors full load current that is taken from the motors nameplate. Search the web for "fractional motor starter switch".
